TITANPRO® PM803

About
Polypropylene homopolymer. Titanpro PM803 is a high flow and also a controlled rheology grade. The base resin meets the requirements of the U.S. Food and Drug Administration as specified in 21 CFR 177.1520(a)(1)(i) and (c)1.1a. The adjuvant meet their respective FDA regulations and 21 CFR 177.1520(b). In summary, this resin meets the FDS criteria covering safe use of polyolefin articles and component of articles intended for food contact use. TSCA Registry: CAS# 9003-07-0 APPLICATIONS: Thin walled injection molding (TWIM) articles and disposable containers and lids, party plates, pen barrels. Characteristics: Low molded in stress, good clarity, good balance of stiffness and impact strength, specifically designed for short cycle time and low warpage. FABRICATION: Equipment – ram or screw injection machines and techniques – standard processing.&&

About

Polypropylene homopolymer. Titanpro PM803 is a high flow and also a controlled rheology grade. The base resin meets the requirements of the U.S. Food and Drug Administration as specified in 21 CFR 177.1520(a)(1)(i) and (c)1.1a. The adjuvant meet their respective FDA regulations and 21 CFR 177.1520(b). In summary, this resin meets the FDS criteria covering safe use of polyolefin articles and component of articles intended for food contact use. TSCA Registry: CAS# 9003-07-0 APPLICATIONS: Thin walled injection molding (TWIM) articles and disposable containers and lids, party plates, pen barrels. Characteristics: Low molded in stress, good clarity, good balance of stiffness and impact strength, specifically designed for short cycle time and low warpage. FABRICATION: Equipment – ram or screw injection machines and techniques – standard processing.&&

Product Description
Supplier	LOTTE
Generic	PP homopolymerization
Material Status	Commercial: Active
Features	Good Rigidity,Low warping,High impact resistance,Quick molding cycle,Food contact compliance,Rigid-tough balance,Homopolymer
Availabilitys	Asia Pacific
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.900	g/cm³	ASTM D1505
Melt Flow Rate
230℃，2.16kg	50	g/10min	ASTM D1238
Water absorption rate
24hr	0.020	%	ASTM D570

IMPACT	Nominal value	Unit	Test method
Impact strength of cantilever beam notch
23℃	20	J/m	ASTM D256-A

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature
0.45 MPa, unannealed	120	℃	ASTM D648

MECHANICAL	Nominal value	Unit	Test method
Rockwell hardness
R-level	108		ASTM D785
tensile strength
yield	34.3	MPa	ASTM D638
Tensile strain
yield	10	%	ASTM D638
Bending modulus	1770	MPa	ASTM D790B

Notes
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.