| About |
|---|
| Torelina® A503-X05 is a Polyphenylene Sulfide (PPS) product filled with 30% glass fiber. It is available in Asia Pacific, Europe, or North America. Primary characteristic: flame rated.&& |
| Product Description | |
|---|---|
| Supplier | Toray |
| Material Status | Commercial: Active |
| Features | V-0 |
| Availabilitys | Europe,Asia Pacific,North America |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.57 | g/cm³ | ISO 1183 |
| Shrinkage rate | Internal Method | ||
| TD：3.0 mm | 0.90 | % | Internal Method |
| MD：3.0 mm | 0.30 | % | Internal Method |
| Water Absorption | |||
| 23℃，24hr | 0.020 | % | ISO 62 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 8.0 | kJ/m² | ISO 179 |
| Charpy Unnotch Impact strength | |||
| 23℃ | 30 | kJ/m² | ISO 179 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature HDT | |||
| 1.8 MPa, unannealed | >260 | ℃ | ISO 75-2/A |
| Melting temperature | 278 | ℃ | ISO 11357-3 |
| Coeff. of linear thermal expansion | |||
| TD | 3.9E-5 | 1/℃ | ISO 11359-2 |
| MD | 2.6E-5 | 1/℃ | ISO 11359-2 |
| ELECTRICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume Resistance | 1.0E+16 | ohms·cm | IEC 60093 |
| Dielectric Strength | 23 | kV/mm | IEC 60243-1 |
| Dielectric Constant | |||
| 23 ℃，1 MHz | 3.20 | IEC 60250 | |
| Dissipation Factor | |||
| 23℃，1 MHz | 2.0E-3 | IEC 60250 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 0.35 mm | V-0 | UL 94 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Rod flow length | |||
| 320℃，1.00 mm | 170 | mm | Internal Method |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile Strength | |||
| Yield yld, 23 ℃ | 140 | MPa | ISO 527-2 |
| Tensile Strain | |||
| Broken BRK, 23 ℃ | 1.5 | % | ISO 527-2 |
| Flexural Modulus | |||
| 23℃ | 12000 | MPa | ISO 178 |
| Flexural Strength | |||
| 23℃ | 220 | MPa | ISO 178 |
| Taber Abrasion | |||
| 1000 cycles | 45.0 | mg | ISO 9352 |
| Rockwell hardness | |||
| R-level | 120 | ISO 2039-2 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 80x80x3mm |
| 3. 60% RH |
| 4. 98 MPa |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |