| About |
|---|
| Lotrène ® Q1018 H is an ethylene-butene copolymer produced in a gas phase reactor. It is designed for delivering competitive performance in most blown film applications. Lotrène ® Q1018 H can be processed at high output rates with moderate extrusion pressure, good bubble stability and gauge control on blown film machine designed for LLDPE. Lotrène ® Q1018 H can advantageously be blended with LDPE or other PE resins used in blown film mono extrusion or coextrusion to improve film properties. Lotrène ® Q1018 H is suited for many applications in the field of consumer, industrial, food or hygiene packaging such as collation shrink, liners, Form-Fill-Seal, heavy-duty sacks, refuse sacks or other bags and non-packaging applications like agricultural films e.g. tunnel and mulching films.&& |
| Product Description | |
|---|---|
| Supplier | TOTAL |
| Generic | Linear low density polyethylene |
| Material Status | Commercial: Active |
| Features | Smoothness,High anti-blocking,Good Gauge Control,Inoxidizability,Low density,Copolymer,Butylene copolymer |
| Availabilitys | Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.918 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 190℃，2.16kg | 1.0 | g/10min | ASTM D1238 |
| film | Nominal value | Unit | Test method |
|---|---|---|---|
| film thickness | |||
| test | 40 | µm | |
| Tensile modulus | ISO 178 | ||
| 1% secant, MD, 40 µ m, blow molded film | 215 | MPa | ISO 178 |
| 1% secant, TD, 40 µ m, blow molded film | 245 | MPa | ISO 178 |
| tensile strength | ISO 527-3 | ||
| MD, yield, 40 µ m, blow molded film | 11.0 | MPa | ISO 527-3 |
| TD, yield, 40 µ m, blow molded film | 11.0 | MPa | ISO 527-3 |
| tensile strength | ISO 527-3 | ||
| MD, fracture, 40 µ m, blow molded film | 38.0 | MPa | ISO 527-3 |
| TD, fracture, 40 µ m, blow molded film | 33.0 | MPa | ISO 527-3 |
| Tensile strain | ISO 527-3 | ||
| MD, fracture, 40 µ m, blow molded film | 800 | % | ISO 527-3 |
| TD, fracture, 40 µ m, blow molded film | 850 | % | ISO 527-3 |
| Drop hammer impact | |||
| 40 µ m, blow molded film | 150 | g | ISO 7765-1 |
| Elmandorf tear strength | ISO 6383-2 | ||
| MD: 40 µ m, blow molded film | 70 | N | ISO 6383-2 |
| TD: 40 µ m, blow molded film | 120 | N | ISO 6383-2 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Vicat Softening Temp | 100 | ℃ | ASTM D1525 3 |
| Melting temperature | 122 | ℃ | Internal Method |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| gloss | |||
| 45 °, 40.0 µ m, blow molded film | 57 | ASTM D2457 | |
| Haze | |||
| 40 µ m, blow molded film | 12 | % | ISO 14782 |
| Process Conditions | |||
|---|---|---|---|
| Extrusion | Nominal value | Unit | Test method |
| Melt temperature | 180 to 220 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. F50 |
| 3. Rate B (120°C/h), Loading 1 (10 N) |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |