TOTAL Polyethylene Lumicene® M 1820 EP

About
Lumicene® mPE M 1820 EP is a Metallocene based Low Density Polyethylene with hexene as comonomer. Lumicene® mPE M 1820 EP is especially dedicated to film applications where outstanding mechanical and optical properties are required. Moreover it offers excellent sealing behavior at low temperature. Lumicene® mPE M 1820 EP can be processed at high output rates with low extrusion pressure, excellent bubble stability and gauge control in comparison with conventional LLDPE and first general metallocene based polyethylene. Furthermore, Lumicene® mPe M 1820 EP has a very low gel level. Applications Lumicene® mPE M1820 EP is suited for many applications such as: Food Packaging Lamination Film Blown Stretch Film Deep-Freeze Packaging FFS bags&&

About

Lumicene® mPE M 1820 EP is a Metallocene based Low Density Polyethylene with hexene as comonomer. Lumicene® mPE M 1820 EP is especially dedicated to film applications where outstanding mechanical and optical properties are required. Moreover it offers excellent sealing behavior at low temperature. Lumicene® mPE M 1820 EP can be processed at high output rates with low extrusion pressure, excellent bubble stability and gauge control in comparison with conventional LLDPE and first general metallocene based polyethylene. Furthermore, Lumicene® mPe M 1820 EP has a very low gel level. Applications Lumicene® mPE M1820 EP is suited for many applications such as: Food Packaging Lamination Film Blown Stretch Film Deep-Freeze Packaging FFS bags&&

Product Description
Supplier	TOTAL
Generic	Linear low density polyethylene
Material Status	Commercial: Active
Features	Optical performance,Good Gauge Control,Low speed solidification point,Inoxidizability,Low density,Hexene copolymers,Low temperature heat sealing
Availabilitys	Europe

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.918	g/cm³	ISO 1183
Melt Flow Rate
190℃，2.16kg	2.0	g/10min	ISO 1133

film	Nominal value	Unit	Test method
film thickness
test	40	µm
tensile strength			ISO 527-3
MD, yield, 40 µ m, blow molded film	10.0	MPa	ISO 527-3
TD, yield, 40 µ m, blow molded film	10.0	MPa	ISO 527-3
tensile strength			ISO 527-3
MD, fracture, 40 µ m, blow molded film	59.0	MPa	ISO 527-3
TD, fracture, 40 µ m, blow molded film	55.0	MPa	ISO 527-3
Tensile strain			ISO 527-3
MD, fracture, 40 µ m, blow molded film	640	%	ISO 527-3
TD, fracture, 40 µ m, blow molded film	710	%	ISO 527-3
Drop hammer impact
40 µ m, blow molded film	> 1000	g	ISO 7765-1
Elmandorf tear strength			ISO 6383-2
MD: 40 µ m, blow molded film	110	N	ISO 6383-2
TD: 40 µ m, blow molded film	160	N	ISO 6383-2

THERMAL	Nominal value	Unit	Test method
Vicat Softening Temp	103	℃	ISO 306
Melting temperature	110	℃	ISO 11357-3

optical performance	Nominal value	Unit	Test method
gloss
45 °, 40.0 µ m, blow molded film	72		ASTM D2457
Haze
40 µ m, blow molded film	5.2	%	ISO 14782

Process Conditions
Extrusion	Nominal value	Unit	Test method
Melt temperature	180 to 230	°C

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.