TOTAL Polyethylene Lumicene® M 1835

About
Lumicene® mPE M 1835 is designed for high performance cast stretch film for mono and multilayer film production. Lumicene® mPE M 1835 is a Metallocene based Low Density Polyethylene with hexene as comonomer. Lumicene® mPE M 1835 brings: High stretchability (up to 350%) in cast stretch film Outstanding Impact and Puncture Resistance Excellent Holding Force Very good Processability on small and large cast lines Very low gel level Lumicene® mPE M 1835 is also suitable for other applications such as Surface Protection, Food Packaging, Hygiene Film and Cast Films. It exhibits an excellent blending-ability with LDPE and LLDPE was observed.&&

About

Lumicene® mPE M 1835 is designed for high performance cast stretch film for mono and multilayer film production. Lumicene® mPE M 1835 is a Metallocene based Low Density Polyethylene with hexene as comonomer. Lumicene® mPE M 1835 brings: High stretchability (up to 350%) in cast stretch film Outstanding Impact and Puncture Resistance Excellent Holding Force Very good Processability on small and large cast lines Very low gel level Lumicene® mPE M 1835 is also suitable for other applications such as Surface Protection, Food Packaging, Hygiene Film and Cast Films. It exhibits an excellent blending-ability with LDPE and LLDPE was observed.&&

Product Description
Supplier	TOTAL
Generic	Linear low density polyethylene
Material Status	Commercial: Active
Features	Excellent Processability,High impact resistance,Low speed solidification point,Inoxidizability,Good Tensile Strength,Low density,Puncture Resistant,Hexene copolymers
Availabilitys	Europe

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.918	g/cm³	ISO 1183
Melt Flow Rate
190℃，2.16kg	3.5	g/10min	ISO 1133

film	Nominal value	Unit	Test method
film thickness
test	20	µm
tensile strength			ISO 527-3
MD, yield, 20 µ m, blow molded film	7.00	MPa	ISO 527-3
TD, yield, 20 µ m, blow molded film	6.40	MPa	ISO 527-3
MD, fracture, 20 µ m, blow molded film	36.0	MPa	ISO 527-3
TD, fracture, 20 µ m, blow molded film	39.0	MPa	ISO 527-3
Tensile strain			ISO 527-3
MD, fracture, 20 µ m, cast thin film	390	%	ISO 527-3
TD, fracture, 20 µ m, cast thin film	590	%	ISO 527-3
Drop hammer impact
20 µ m, cast thin film	710	g	ISO 7765-1
Elmandorf tear strength			ISO 6383-2
MD: 20 µ m, cast thin film	120	N	ISO 6383-2
TD: 20 µ m, cast thin film	180	N	ISO 6383-2

THERMAL	Nominal value	Unit	Test method
Vicat Softening Temp	99.0	℃	ISO 306
Melting temperature	109	℃	ISO 11357-3

optical performance	Nominal value	Unit	Test method
gloss
45 °, 20 µ m, cast thin film	81		ASTM D2457
Haze
20.0 µ m, cast thin film	2.7	%	ISO 14782

Process Conditions
Extrusion	Nominal value	Unit	Test method
Melt temperature	220 to 280	°C
Traction roller	20 to 80	°C

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.