TOTAL Polystyrene Crystal 525L

About
Polystyrene 525L: Is a crystal polystyrene with low residuals that is ideally suited for blending with clear elastomers for extrusion-thermoforming applications that require low odor and taste. Total Petrochemicals 525L can also be used as a cap layer for coextrusion applications that require a glossy finish, or in injection molding. Injection molding applications such as medical and laboratory parts, tumblers and jewel boxes demonstrate the polymer’s ability to be molded with minimal stresses and fast cycles. Application: Blending with clear styrenic elastomers Cutlery Coextrusion capping Medical applications General Information: This material complies with FDA requirements as described in 21 CFR §177.1640. This material holds Underwriters Laboratory recognition 94HB; see UL File E55470 at www.UL.com. USP Class VI Material Safety Data Sheets are available to help customers satisfy their safety needs.&&

About

Polystyrene 525L: Is a crystal polystyrene with low residuals that is ideally suited for blending with clear elastomers for extrusion-thermoforming applications that require low odor and taste. Total Petrochemicals 525L can also be used as a cap layer for coextrusion applications that require a glossy finish, or in injection molding. Injection molding applications such as medical and laboratory parts, tumblers and jewel boxes demonstrate the polymer’s ability to be molded with minimal stresses and fast cycles. Application: Blending with clear styrenic elastomers Cutlery Coextrusion capping Medical applications General Information: This material complies with FDA requirements as described in 21 CFR §177.1640. This material holds Underwriters Laboratory recognition 94HB; see UL File E55470 at www.UL.com. USP Class VI Material Safety Data Sheets are available to help customers satisfy their safety needs.&&

Product Description
Supplier	TOTAL
Generic	PS (GPPS)
Material Status	Commercial: Negative
Features	Good surface appearance,Low Residuals,Quick molding cycle,Low odor,HB
Availabilitys	North America
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.04	g/cm³
Melt Flow Rate
200℃，5.0kg	9.0	g/10min	ASTM D1238
Shrinkage rate
MD	0.40 to 0.70	%	ASTM D955
humidity	< 0.10	%

MECHANICAL	Nominal value	Unit	Test method
Tensile modulus	3030	MPa	ASTM D638
tensile strength	46.2	MPa	ASTM D638
Bending modulus	3100	MPa	ASTM D790
bending strength	93.1	MPa	ASTM D790

THERMAL	Nominal value	Unit	Test method
Vicat Softening Temp	101	℃	ASTM D1525
Hot deformation temperature
annealing	93	℃	ASTM D648

FLAME CHARACTERISTICS	Nominal value	Unit	Test method
Flame retardant level	HB		UL 94

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.