TOTAL Polystyrene Impact 8260

About
POLYSTYRENE IMPACT 8260 is an high impact polystyrene for extrusioin and injection applications. This grade has an improved environmental stress crack resistance in comparison with standard high impact grades. The product has been specifically designed for the production of refrigerator part: inner liners, door liners, injected parts etc. This grade is also proposed for the production of packaging intended for products likely to cause stress cracking e.g. fats, oil… POLYSTYRENE IMPACT 8260 retains good mechanical properties at low temperatures making this grade suitable for frozen packaging; it also affords good printing performance. Applications Sheet for thermoforming, fridges liners, low temperature packaging applications (ice cream boxes and lids), packaging for aggressive foodstuffs, matt finish, soft touch.&&

About

POLYSTYRENE IMPACT 8260 is an high impact polystyrene for extrusioin and injection applications. This grade has an improved environmental stress crack resistance in comparison with standard high impact grades. The product has been specifically designed for the production of refrigerator part: inner liners, door liners, injected parts etc. This grade is also proposed for the production of packaging intended for products likely to cause stress cracking e.g. fats, oil… POLYSTYRENE IMPACT 8260 retains good mechanical properties at low temperatures making this grade suitable for frozen packaging; it also affords good printing performance. Applications Sheet for thermoforming, fridges liners, low temperature packaging applications (ice cream boxes and lids), packaging for aggressive foodstuffs, matt finish, soft touch.&&

Product Description
Supplier	TOTAL
Generic	PS (HIPS)
Material Status	Commercial: Active
Features	High impact resistance,Good Printability
Availabilitys	Europe
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.04	g/cm³	ISO 1183
Apparent density	0.60	g/cm³	ISO 60
Melt Flow Rate
200℃，5.0kg	2.8	g/10min	ASTM D1238
Shrinkage rate	0.40 to 0.70	%	ISO 294-4
Water absorption rate
23℃，24hr	< 0.10	%	ISO 62

MECHANICAL	Nominal value	Unit	Test method
Tensile modulus
23℃	1600	MPa	ISO 527-2
tensile strength			ISO 527-2
Yield, 23 ℃	20.0	MPa
Fracture, 23 ℃	25.0	MPa
Tensile strain
Fracture, 23 ℃	> 60	%	ISO 527-2
Bending modulus
23℃	1600	MPa	ISO 178

IMPACT	Nominal value	Unit	Test method
Charpy Notched Impact Strength
23℃	11	kJ/m²	ISO 179/1eA
Impact strength of cantilever beam notch
23℃	11	kJ/m²	ISO 180-1A

THERMAL	Nominal value	Unit	Test method
Vicat Softening Temp
A50	99.0	℃	ISO 306/A50
B50	90.0	℃	ISO 306
Linear coefficient of thermal expansion
MD	9.1E-5	1/℃	ISO 11359-2

Electrical performance	Nominal value	Unit	Test method
Surface resistivity	> 1.0E+14	ohms	IEC 60093
Dielectric strength
23℃	150	kV/mm	IEC 60243-1

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.