| About |
|---|
| Product Description: TREXPRENE ® A88SCI-HF is a heat stabilized PP/EPDM based Thermoplastic Vulcanized Elastomer (TPV) which contains a lubricant/slip package for lower co-efficient of friction and anti-wear properties versus normal TPV’s. This compound is formulated in pre-color form primarily for under-hood or interior applications. This material can be processed using Injection Molding, Extrusion, Blow Molding or other melt processing techniques.&& |
| Product Description | |
|---|---|
| Supplier | Mitsubishi |
| Generic | TPV |
| Material Status | Commercial: Active |
| Features | Smoothness,Low coefficient of friction,Lubricating,Good wear resistance,Heat Stabilized |
| Availabilitys | North America |
| Process Methods | Extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.870 to 0.930 | g/cm³ | ISO 1183 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shore A, 15 seconds | 82 to 90 | ISO 868 | |
| Wear Resistance | No appreciable loss of grain, texture or color | ASTM D3844 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| TD, fracture | 10.2 | MPa | ISO 37 |
| TD, 100% strain | 5.90 | MPa | ISO 37 |
| Tensile strain | |||
| TD, fracture | 670 | % | ISO 37 |
| tear strength | |||
| TD | 42 | kN/m | ISO 34-1 |
| Compression deformation | |||
| 70℃，22 hr | 47 | % | ISO 815 |
| 70℃，22 hr | 47 | % | ASTM D395B |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Embrittlement temperature | -51.0 | ℃ | ASTM D746 |
| Brittleness Temperature（Type B） | -51.0 | ℃ | ISO 812 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Burning rate | 32 | mm/min | ISO 3795 |
| Fogging（Dry Fog） | 79 | % | SAE J1756 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Color stability | |||
| to Burnt Gas，AATCC Rating：60℃ | > 4.00 | ||
| to Burnt Gas，Change in Color：60℃ | Delta E < 3 | ||
| To Burnt Gas, Yellowness Index: 60 ℃ | < 2.00 | YI | |
| to Light | Delta E < 3 | ||
| Linting | Rating less than 2 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 1000 cycles CS10 Wheel (500 g load) |
| 3. Type 1, 20 in/min |
| 4. Method Ba, Angle (Unnicked), 20 in/min |
| 5. Type A |
| 6. ISO 105-G02, AATCC TM 23, 168 h |
| 7. SAE J2412, ISO 105-B06, Cond. 5, 1,240.8 kJ/m² |
| 8. LP-463KB-37-01, Method A |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |