| About |
|---|
| Triax 1120 is an ABS (Acrylonitrile Butadiene Styrene) and polyamide alloy for injection molding. FEATURES Excellent processability Good chemical resistance Good fatigue performance Excellent abrasion resistance UL 94HB certified APPLICATIONS Housings Handles and shrouds Automotive fasteners Automotive interior applications&& |
| Product Description | |
|---|---|
| Supplier | INEOS |
| Generic | ABS+PA |
| Material Status | Commercial: Active |
| Features | Excellent Processability,Fatigue resistance,Good wear resistance,Solvent resistance,HB |
| Availabilitys | North America,Latin America |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.06 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 250℃，5.0kg | 6.5 | g/10min | ASTM D1238 |
| film | Nominal value | Unit | Test method |
|---|---|---|---|
| Elastic modulus | |||
| MD | 56.9 | MPa | ASTM D882 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | ASTM D256 | ||
| -40℃ | 75 | J/m | ASTM D256 |
| 23℃ | 750 | J/m | ASTM D256 |
| Dart impact equipped with measuring instruments | |||
| Total Energy | 4.07 | J | ASTM D3763 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 62.2 | ℃ | ASTM D648 |
| 0.45 MPa, unannealed | 87.8 | ℃ | ASTM D648 |
| Linear coefficient of thermal expansion | |||
| MD | 1.1E-4 | 1/℃ | ASTM D696 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | 3.2E+13 | ohms | ASTM D257 |
| Volume resistivity | 9.0E+13 | ohms·cm | ASTM D257 |
| Dielectric constant | |||
| 100 Hz | 3.50 | ASTM D150 | |
| Dissipation factor | |||
| 1 MHz | 3.9E-6 | ASTM D150 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | HB | UL 94 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| gloss | |||
| 60° | 91 | ASTM D523 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| Yield, 23 ℃ | 40.0 | MPa | ASTM D638 |
| Bending modulus | 1170 | MPa | ASTM D790 |
| Rockwell hardness | |||
| R-level | 90 | ASTM D785 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 88 to 93 | °C | |
| Drying time | 2.0 to 4.0 | hr | |
| Processing (melt) temperature | 238 to 271 | °C | |
| Mold temperature | 38 to 66 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |