| About |
|---|
| Triax 1185 is an ABS (Acrylonitrile Butadiene Styrene) polyamide alloy for injection molding. FEATURES Excellent processability Good chemical resistance Excellent abrasion resistance Excellent surface appearance UL 94HB certified APPLICATIONS Components for recreation vehicles Industrial and consumer applications Snowmobiles, ATVs, Side by sides&& |
| Product Description | |
|---|---|
| Supplier | INEOS |
| Generic | ABS+PA |
| Material Status | Commercial: Active |
| Features | Excellent Processability,Good surface appearance,Good wear resistance,Solvent resistance,HB |
| Availabilitys | North America,Latin America |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.07 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 250℃，5.0kg | 11 | g/10min | ASTM D1238 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| Yield, 23 ℃ | 33.7 | MPa | ASTM D638 |
| Bending modulus | 1320 | MPa | ASTM D790 |
| film | Nominal value | Unit | Test method |
|---|---|---|---|
| Elastic modulus | |||
| MD | 15.4 | MPa | ASTM D882 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | ASTM D256 | ||
| -18℃ | 800 | J/m | ASTM D256 |
| 23℃ | 1000 | J/m | ASTM D256 |
| Dart impact equipped with measuring instruments | |||
| Total Energy | 3.95 | J | ASTM D3763 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 51.1 | ℃ | ASTM D648 |
| 0.45 MPa, unannealed | 82.2 | ℃ | ASTM D648 |
| Vicat Softening Temp | 196 | ℃ | ASTM D1525 2 |
| Linear coefficient of thermal expansion | |||
| MD | 1.2E-4 | 1/℃ | ASTM D696 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | HB | UL 94 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| gloss | |||
| 60° | 93 | ASTM D523 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 88 to 93 | °C | |
| Drying time | 2.0 to 4.0 | hr | |
| Processing (melt) temperature | 238 to 271 | °C | |
| Mold temperature | 38 to 93 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Rate B (120°C/h), Loading 1 (10 N) |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |