Tritan™ MX810

About
Eastman Tritan™ MX810 is an amorphous copolyester with excellent appearance and clarity. Its most outstanding features are excellent toughness, hydrolytic stability, and heat and chemical resistance. This new generation copolyester can also be molded into various applications without incorporating high levels of residual stress. Eastman Tritan™ Copolyester MX810 has been tested for FDA/ISO 10993 and USP Class VI Biological Evaluation testing after Gamma and ETO sterilization.&&

About

Eastman Tritan™ MX810 is an amorphous copolyester with excellent appearance and clarity. Its most outstanding features are excellent toughness, hydrolytic stability, and heat and chemical resistance. This new generation copolyester can also be molded into various applications without incorporating high levels of residual stress. Eastman Tritan™ Copolyester MX810 has been tested for FDA/ISO 10993 and USP Class VI Biological Evaluation testing after Gamma and ETO sterilization.&&

Product Description
Supplier	Eastman
Generic	PCTG
Material Status	Commercial: Active
Features	Excellent Processability,Good Clarity,Good flexibility,High impact resistance,Hydrolysis stability,Quick molding cycle,High Heat Resistance,Radiation disinfection,Solvent resistance,Ethylene oxide disinfection,Amorphous
Availabilitys	Africa & Middle East ,North America,Latin America,Asia Pacific,Europe

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.17	g/cm³	ASTM D792
Shrinkage rate
MD	0.50 to 0.70	%	ASTM D955

IMPACT	Nominal value	Unit	Test method
Impact strength of cantilever beam notch
23℃	650	J/m	ASTM D256
23℃	No Break		ASTM D4812

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature
1.8 MPa, unannealed	92.0	℃	ASTM D648
0.45 MPa, unannealed	109	℃	ASTM D648

optical performance	Nominal value	Unit	Test method
Transmittance
total	92.0	%	ASTM D1003
Haze	< 1.0	%	ASTM D1003

MECHANICAL	Nominal value	Unit	Test method
Tensile modulus
23℃	1590	MPa	ASTM D638
tensile strength
Fracture, 23 ℃	53.0	MPa	ASTM D638
Yield, 23 ℃	44.0	MPa	ASTM D638
Tensile strain
Fracture, 23 ℃	140	%	ASTM D638
Yield, 23 ℃	7.0	%	ASTM D638
Bending modulus
23℃	1590	MPa	ASTM D790
bending strength
Yield, 23 ℃	66.0	MPa	ASTM D790
Rockwell hardness
R-level	115		ASTM D785

Process Conditions
injection	Nominal value	Unit	Test method
Drying temperature	88	°C
Drying time	4.0 to 6.0	hr
Processing (melt) temperature	260 to 282	°C
Mold temperature	38 to 66	°C

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.