Tritan™ TX1800

About
Eastman Tritan™ Copolyester TX1800 is an amorphous copolyester specifically developed for use in blow molding and profile extrusion applications. Its most outstanding features are excellent toughness, hydrolytic stability, heat resistance, and chemical resistance. In addition, this new generation copolyester offers excellent appearance and clarity. Eastman Tritan™ Copolyester TX1800 may be used in repeated use food contact articles under United States Food and Drug Administration (FDA) regulations. This product is certified to NSF/ANSI Standard 51 for Food Equipment Materials.&&

About

Eastman Tritan™ Copolyester TX1800 is an amorphous copolyester specifically developed for use in blow molding and profile extrusion applications. Its most outstanding features are excellent toughness, hydrolytic stability, heat resistance, and chemical resistance. In addition, this new generation copolyester offers excellent appearance and clarity. Eastman Tritan™ Copolyester TX1800 may be used in repeated use food contact articles under United States Food and Drug Administration (FDA) regulations. This product is certified to NSF/ANSI Standard 51 for Food Equipment Materials.&&

Product Description
Supplier	Eastman
Generic	PCTG
Material Status	Commercial: Active
Features	Excellent Processability,Good Clarity,Good flexibility,Good surface appearance,High impact resistance,Hydrolysis stability,Food contact compliance,High Heat Resistance,Solvent resistance,Amorphous
Availabilitys	Africa & Middle East ,North America,Latin America,Asia Pacific,Europe
Process Methods	Injection Stretch Blow Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.18	g/cm³	ASTM D792

optical performance	Nominal value	Unit	Test method
Refractive index	91.0		ASTM D542
Transmittance	1.0	%	ASTM D1003

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature
0.45 MPa, unannealed	101	℃	ASTM D648
1.8 MPa, unannealed	85	℃	ASTM D648

FLAME CHARACTERISTICS	Nominal value	Test method
Flame retardant level
1.50mm	HB	UL-94
3.00mm	HB	UL-94

IMPACT	Nominal value	Unit	Test method
Impact strength of cantilever beam notch
23℃	842	J/m	ASTM D256

MECHANICAL	Nominal value	Unit	Test method
Rockwell hardness	110	R 级	ASTM D785
tensile strength
23℃	45	MPa	ASTM D638
Tensile strain
Fracture, 23 ℃	139	%	ASTM D638
Tensile modulus
23℃	1609	MPa	ASTM D638
bending strength
23℃	64	MPa	ASTM D790
Bending modulus
23℃	1522	MPa	ASTM D790

Process Conditions
injection	Nominal value	Unit	Test method
Drying temperature	90	°C
Drying time	4.0-6.0	Hr
Injection temperature
Mold temperature	30-60	°C

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.