| About |
|---|
| Product Description | |
|---|---|
| Supplier | Evonik |
| Generic | PA Not specified |
| Material Status | Commercial: Active |
| Technical Data | |||
|---|---|---|---|
| MECHANICAL | Nominal value | Unit | Test method |
| Tensile modulus | 1400 | MPa | ISO 527 |
| tensile strength | 60 | MPa | ISO 527 |
| Yield stress | 60 | MPa | ISO 527 |
| Yield strain | 8 | % | ISO 527 |
| Stress at 50% strain | 42 | MPa | ISO 527 |
| The nominal strain at fracture, ε TB | 180 | % | ISO 527 |
| Tensile creep modulus, 0.5% strain, 1h | 1300 | MPa | ISO 899-1 |
| Tensile creep modulus, 0.5% strain, 1000h | 700 | MPa | ISO 899-1 |
| Charpy impact strength,+23 ° C | N | kJ/m² | ISO 179/1eU |
| Charpy impact strength -30 ° C | N | kJ/m² | ISO 179/1eU |
| Charpy notch impact strength,+23 ° C | 16 / 11 | kJ/m² | ISO 179/1eA |
| fault type | C / C | – | – |
| Charpy notch impact strength -30 ° C | 14 / 10 | kJ/m² | ISO 179/1eA |
| fault type | C / C | – | – |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Melting temperature | 255 | °C | ISO 11357-1/-3 |
| Glass transition temperature | 140 | °C | ISO 11357-1/-2 |
| Hot deformation temperature | |||
| 1.80 MPa | 105 | °C | ISO 75-1/-2 |
| 0.45 MPa | 122 | °C | ISO 75-1/-2 |
| Vicat Softening Temp | |||
| 10 N，50 K/h | 137 | °C | ISO 306 |
| 50 N，50 K/h | 130 | °C | ISO 306 |
| Linear coefficient of thermal expansion | |||
| parallel | 90 | E-6/K | ISO 11359-1/-2 |
| normal | 90 | E-6/K | ISO 11359-1/-2 |
| Melting temperature | 255 | °C | ASTM D 3418 |
| physical characteristics | Nominal value | Unit | Test method |
|---|---|---|---|
| Water absorption rate | 3.5 | % | Sim. to ISO 62 |
| Hygroscopicity | 1.5 | % | Sim. to ISO 62 |
| dense | 1020 | kg/m³ | ISO 1183 |
| Shaw D hardness | 81[b] | – | ISO 7619-1 |
| dense | 1020 | kg/m³ | ASTM D 792 |
| Burning behavior. | Nominal value | Unit | Test method |
|---|---|---|---|
| Burning behavior. At thickness h | HB | class | IEC 60695-11-10 |
| Test thickness | 0.8 | mm | – |
| Burning behavior | |||
| 1.5 mm | HB | class | IEC 60695-11-10 |
| Test thickness | 1.6 | mm | – |
| Burning rate, FMVSS, thickness 1 mm | 0.1 | mm/min | ISO 3795 (FMVSS 302) |
| Electrical characteristics | Nominal value | Unit | Test method |
|---|---|---|---|
| Relative dielectric constant, 100Hz | 3.6 | – | IEC 62631-2-1 |
| Relative dielectric constant, 1MHz | 3.2 | – | IEC 62631-2-1 |
| Dissipation factor, 100Hz | 115 | E-4 | IEC 62631-2-1 |
| Dissipation factor, 1MHz | 325 | E-4 | IEC 62631-2-1 |
| Volume resistivity ρ V | >1E13 | Ohm*m | IEC 62631-3-1 |
| Surface resistance, RSA | 1E13 | Ohm | IEC 62631-3-2 |
| Surface resistivity σ A | 1E14 | Ohm per square | IEC 62631-3-2 |
| Electrical strength, AC, S20/S20 | 27 | kV/mm | IEC 60243-1 |
| CTI, test solution A, 50 drop value | 600 | – | IEC 60112 |
| Rheological properties | Nominal value | Unit | Test method |
|---|---|---|---|
| Melt Volume Rate | 8.2 | cm³/10min | ISO 1133 |
| temperature | 280 | °C | – |
| load | 2.16 | kg | – |
| Forming shrinkage | |||
| parallel | 0.7 | % | ISO 294-4, 2577 |
| normal | 0.7 | % | ISO 294-4, 2577 |
| Mold temperature | 80 | °C | – |
| Melt Temperature | 280 | °C | – |
| Rheological calculation characteristics | Nominal value | Unit | Test method |
|---|---|---|---|
| Melt density | 900 | kg/m³ | – |
| Melt thermal conductivity | 0.25 | W/(m K) | – |
| Melt heat capacity specifications | 2490 | J/(kg K) | – |
| Spray temperature | 120 | °C | – |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |