| About |
|---|
| ULTEM™ AMHU1010F filament is a polyetherimide product for 3D printing applications manufactured fromULTEM™ HU1010 resin. The filament is biocompatible (ISO 10993 or USP Class VI) and printed parts can be gamma, EtO or steam sterilized. This filament can be used for food and drug packaging and medical device manufacturing, from conceptual modeling to functional prototyping and end-use parts. Filament spools can be linked to resin raw material batch to help ensure material compliance and traceability.* *It is the responsibility of the finished device manufacturer to determine the suitability of all the component parts and materials used in their finished products. SABIC does not recommend and will not support the use of any of SABICu0027s products in medical devices intended to remain continuously in the human body for longer than 29 days. |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | Polyetherimide |
| Material Status | Commercial: Active |
| Availabilitys | North America,Latin America,Europe |
| Technical Data | |||
|---|---|---|---|
| MECHANICAL | Nominal value | Unit | Test method |
| Tensile modulus | |||
| XY direction | 2750 | MPa | |
| XZ direction | 2870 | MPa | |
| ZX direction | 2840 | MPa | |
| Tensile strength | |||
| XY direction: fracture | 73.0 | MPa | |
| XZ direction: fracture | 80.0 | MPa | |
| ZX direction: fracture | 34.0 | MPa | |
| Tensile strain | |||
| XY direction, fracture | 4.0 | % | |
| XZ direction, fracture | 3.8 | % | |
| ZX direction, fracture | 1.3 | % | |
| Bending modulus | |||
| XY direction | 2520 | MPa | |
| XZ direction | 2840 | MPa | |
| ZX direction | 2380 | MPa | |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| XY direction, 23 ℃ | 31 | J/m | |
| XZ direction, 23 ℃ | 37 | J/m | |
| ZX direction, 23 ℃ | 30 | J/m | |
| Notched impact strength of cantilever beam | |||
| XY direction: 23 ℃ | 270 | J/m | |
| XZ direction: 23 ℃ | 240 | J/m | |
| ZX direction: 23 ℃ | 130 | J/m |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| XY direction: 1.8 MPa, unannealed, 3.20 mm | 211 | ℃ | |
| XZ direction: 1.8 MPa, unannealed, 3.20 mm | 210 | ℃ | |
| ZX direction: 1.8 MPa, unannealed, 3.20 mm | 208 | ℃ | |
| Vicat Softening Temp | 220 | ℃ | ASTM D1525 4 |
| Linear coefficient of thermal expansion | |||
| Flow: XY direction | 5.1E-5 | 1/℃ | |
| Flow: ZX direction | 5.3E-5 | 1/℃ | |
| Flow: XZ direction | 5.3E-5 | 1/℃ | |
| TD: XZ direction | 5.2E-5 | 1/℃ | |
| TD: XY direction | 5.3E-5 | 1/℃ | |
| TD: ZX direction | 5.3E-5 | 1/℃ |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | |||
| XY direction | 6.2E+14 | ohms·cm | |
| XZ direction | 1.3E+15 | ohms·cm | |
| Dielectric constant | |||
| XY direction: 1.90 GHz | 2.90 | ||
| XZ direction: 1.90 GHz | 2.94 | ||
| Dissipation factor | |||
| XY direction: 1.90 GHz | 3.0E-3 | ||
| XZ direction: 1.90 GHz | 3.0E-3 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| XZ direction, 1.50 mm | V-0 | ||
| XY direction, 1.50 mm | V-0 | ||
| ZX direction, 1.50 mm | V-0 | ||
| XY direction, 3.00 mm | 5VA |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |