| About |
|---|
| Transparent, enhanced flow Polyetherimide (Tg 217C). ECO Conforming. For medical devices and pharmaceutical applications. Healthcare management of change, biocompatible (ISO 10993 or USP Class VI); food contact compliant; Steam, Gamma, EtO; and E-beam sterilizable.&& |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | Polyetherimide |
| Material Status | Commercial: Active |
| Features | ECO,Biocompatible,V-0,Ethylene oxide disinfection,5VA,High liquidity,Food contact compliance,Steam sterilized,V-2 |
| Availabilitys | Europe,North America,Asia Pacific |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.27 | g/cm³ | ISO 1183 |
| Melt Flow Rate | |||
| 337℃，6.6kg | 18 | g/10min | ASTM D1238 |
| Melt Volume Rate | |||
| 360℃，5 kg | 25.0 | cm³/10min | ISO 1133 |
| Shrinkage rate | |||
| MD：3.2 mm | 0.5~0.7 | % | |
| Water absorption rate | |||
| Saturation, 23 ℃ | 1.3 | % | ISO 62 |
| Equilibrium, 23 ℃, 50% RH | 0.70 | % | ISO 62 |
| Equilibrium, 23 ℃ | 1.3 | % | ASTM D570 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 3200 | MPa | ISO 527-1-2 |
| tensile strength | |||
| fracture | 105 | MPa | ASTM D638 |
| yield | 110 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | 60 | % | ISO 527-2/5 |
| yield | 6.0 | % | ISO 527-2/5 |
| Bending modulus | |||
| 100 mm span | 3520 | MPa | ASTM D790 |
| 50 mm span | 3420 | MPa | ASTM D790 |
| Bending modulus | 3300 | MPa | ISO 178 |
| bending strength | |||
| Yield, 50 mm span | 174 | MPa | ASTM D790 |
| Yield, 100 mm span | 165 | MPa | ASTM D790 |
| Taber abraser | |||
| 1000 cycles, 1000 g, CS-17 wheels | 10.0 | mg | ASTM D1044 |
| Rockwell hardness | |||
| M-level | 109 | ASTM D785 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 3.0 | kJ/m² | ISO 179/1eA |
| Impact strength of cantilever beam notch | |||
| -30℃ | 5.0 | kJ/m² | ISO 180-1A |
| 23℃ | 5.0 | kJ/m² | ISO 180-1A |
| Dart impact (23 ℃) | 33.0 | J | ASTM D3763 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed, 64 mm span | 193 | ℃ | ISO 75-2/Af |
| 1.8 MPa, unannealed, 6.4 mm | 199 | ℃ | ASTM D648 |
| 0.45 MPa, unannealed, 6.4 mm | 207 | ℃ | ASTM D648 |
| Vicat Softening Temp | |||
| B50 | 211 | ℃ | ISO 306 |
| B120 | 212 | ℃ | ISO 306/B120 |
| Linear coefficient of thermal expansion | |||
| TD：-40~40℃ | 5.0E-5 | 1/℃ | ISO 11359-2 |
| MD：-40~40℃ | 5.0E-5 | 1/℃ | ISO 11359-2 |
| Thermal conductivity coefficient | 0.22 | W/m/K | ASTM C177 |
| Relative temperature index | |||
| Electrical performance | 170 | ℃ | UL 746 |
| Strength mechanical performance | 170 | ℃ | UL 746 |
| Impact mechanical performance | 170 | ℃ | UL 746 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.0E+17 | ohms·cm | ASTM D257 |
| Dielectric strength | |||
| 1.6 mm in air | 33 | kV/mm | ASTM D149 |
| 1.6 mm in oil | 28 | kV/mm | ASTM D149 |
| Dielectric constant | |||
| 1 kHz | 3.15 | ASTM D150 | |
| Dissipation factor | |||
| 1 kHz | 1.3E-3 | ASTM D150 | |
| 2.45 GHz | 2.5E-3 | ASTM D150 | |
| Arc resistance | PLC 5 | ASTM D495 | |
| Compared to the leakage tracing index | PLC 4 | UL 746 | |
| High Arc Burning Index (HAI) | PLC 3 | UL 746 | |
| High voltage arc marking rate (HVTR) | PLC 2 | UL 746 | |
| Hot wire ignition (HWI) | PLC 1 | UL 746 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 0.71 mm | V-2 | UL 94 | |
| 0.75 mm | V-0 | UL 94 | |
| 3.00 mm | 5VA | UL 94 | |
| Extreme oxygen index | 44 | % | ASTM D2863 |
| NBS smoke density | |||
| Flaming，Ds，4 min | 2.00 | ASTM E662 |
| Process Conditions | |||
|---|---|---|---|
| Injection | Nominal value | Unit | Test method |
| drying temperature | 149 | °C | |
| Drying time | 4.0~6.0 | hrs | |
| Drying time, maximum | 24 | hr | |
| Recommended maximum moisture content | 0.020 | % | |
| Suggested injection volume | 40~60 | % | |
| Temperature at the rear of the barrel | 332~399 | °C | |
| Temperature in the middle of the barrel | 338~399 | °C | |
| Front temperature of material barrel | 343~399 | °C | |
| Nozzle temperature | 343~399 | °C | |
| Processing (melt) temperature | 349~399 | °C | |
| Mold temperature | 135~163 | °C | |
| Back pressure | 0.345~ 0.689 | MPa | |
| Screw speed | 40~70 | rpm | |
| Exhaust hole depth | 0.025~0.076 | mm | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 0.20 in/min |
| 3. Type I, 0.20 in/min |
| 4. 0.10 in/min |
| 5. 0.051 in/min |
| 6. 0.079 in/min |
| 7. at Yield |
| 8. 80*10*4 sp=62mm |
| 9. 80*10*4 mm |
| 10. Rate A (50°C/h), Loading 2 (50 N) |
| 11. Tungsten Electrode |
| 12. Surface |
| 13. 4 min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |