Ultradur® B 4300 G2

About
Ultradur B 4300 G2 is an easy flowing injection molding PBT with 10% glass fiber reinforcement for rigid, tough, and dimensionally stable parts. Applications Typical applications include timer dials, toggles, knobs, parts for thermostats, oven-door handles, toaster housings and grills.&&

Product Description
Supplier	BASF
Generic	polybutylene terephthalate
Material Status	Commercial: Active
Features	Good Rigidity,Good flexibility,Good Dimensional Stability,Good liquidity,HB
Availabilitys	North America,Asia Pacific,Europe
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.37	g/cm³	ASTM D792 , ISO 1183
Melt Volume Rate
250℃，2.16 kg	16.0	cm³/10min	ISO 1133
Shrinkage rate
MD：3.2 mm	0.80	%
TD	1.4	%	ISO 294-4
MD	1.2	%	ISO 294-4
Water absorption rate
saturated	0.40	%	ASTM D570
Saturation, 23 ℃	0.40	%	ISO 62
Balance, 50% RH	0.20	%	ASTM D570
Equilibrium, 23 ℃, 50% RH	0.20	%	ISO 62
Viscosity value
Reduced viscosity	115.0	ml/g	ISO 1628

MECHANICAL	Nominal value	Unit	Test method
Tensile modulus
23℃	4500	MPa	ISO 527-2
tensile strength
Fracture, 23 ℃	90.0	MPa	ASTM D638 , ISO 527-2
Fracture, -40 ℃	111	MPa	ISO 527-2
Tensile strain
Fracture, 23 ℃	3.5	%	ASTM D638 , ISO 527-2
Fracture, -40 ℃	2.8	%	ISO 527-2
Bending modulus
23℃	3930	MPa	ASTM D790
23℃	3900	MPa	ISO 178

IMPACT	Nominal value	Unit	Test method
Charpy Notched Impact Strength
23℃	5.0	kJ/m²	ISO 179
Charpy Unnotch Impact strength			ISO 179
-30℃	38	kJ/m²	ISO 179
23℃	40	kJ/m²	ISO 179
Impact strength of cantilever beam notch
23℃	48	J/m	ASTM D256
23℃	5.0	kJ/m²	ISO 180

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature
0.45 MPa, unannealed	220	℃	ASTM D648，ISO 75-2/B
1.8 MPa, unannealed	200	℃	ASTM D648，ISO 75-2/A
Melting peak temperature	223	℃	ASTM D3418 , ISO 3146
Linear coefficient of thermal expansion
MD	4.5E-5	1/℃
0.75 mm	130	℃	UL 746
1.5 mm	130	℃	UL 746
3.0 mm	130	℃	UL 746
0.75 mm	125	℃	UL 746
1.5 mm	125	℃	UL 746
3.0 mm	125	℃	UL 746
Relative temperature index			UL 746
Electrical performance			UL 746
Impact mechanical performance			UL 746
0.75 mm	125	℃	UL 746
1.50 mm	125	℃	UL 746
3.00 mm	140	℃	UL 746

Electrical performance	Nominal value	Unit	Test method
Surface resistivity
1.5 mm	1.0E+13	ohms	ASTM D257
—	1.0E+13	ohms	IEC 60093
Volume resistivity
1.50 mm	> 1.0E+13	ohms·cm	ASTM D257
—	> 1.0E+13	ohms·cm	IEC 60093
Dielectric constant			IEC 60250
100 Hz	3.60		IEC 60250
1 MHz	3.60		IEC 60250
Dissipation factor			IEC 60250
100 Hz	1.2E-3		IEC 60250
1 MHz	0.015		IEC 60250
Compared to the leakage tracing index	300	V	IEC 60112

FLAME CHARACTERISTICS	Nominal value	Test method
Flame retardant level		UL 94
1.50 mm	HB	UL 94
3.00 mm	HB	UL 94

Process Conditions
injection	Nominal value	Unit	Test method
Drying temperature	100 to 120	°C
Drying time	4.0	hr
Recommended maximum moisture content	0.040	%
Processing (melt) temperature	250 to 270	°C
Mold temperature	60 to 100	°C
Injection pressure	3.50 to 12.5	MPa
Injection speed	快速
Back pressure	< 1.00	MPa

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.