| About |
|---|
| Low-warpage, easy-flowing injection molding grade with 10% glass fibres for technical parts, for which dimensional stability is very important (eg, housings, plug-and-socket connectors).&& |
| Product Description | |
|---|---|
| Supplier | BASF |
| Generic | PBT+ASA |
| Material Status | Commercial: Active |
| Features | Low warping,Good Dimensional Stability,Good liquidity |
| Availabilitys | Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.31 | g/cm³ | ISO 1183 |
| Water absorption rate | |||
| 23℃，50% RH | 0.20 | % | ISO 62 |
| 23℃，24hr | 0.40 | % | ISO 62 |
| Melt Flow Rate | |||
| 275℃，2.16kg | 35 | g/10min | ISO 1133 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| 23℃ | 75 | MPa | ISO 527-2 |
| Tensile strain | |||
| Fracture, 23 ℃ | 2.9 | % | ISO 527-2 |
| Tensile modulus | |||
| 23℃ | 4500 | MPa | ISO 527-2 |
| Tensile creep modulus | |||
| 1000 hr | 3300 | MPa | ISO 899-1 |
| bending strength | |||
| 23℃ | 119 | MPa | ISO 178 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 105 | ℃ | ISO 75-2/Af |
| 0.45 MPa, unannealed | 190 | ℃ | ISO 75-2/Bf |
| Melting temperature | 223 | ℃ | ISO 11357-3 |
| Linear coefficient of thermal expansion | |||
| MD | 5.5E-5 | 1/℃ | ISO 11359-2 |
| Thermal conductivity coefficient | 0.27 | W/m/K | DIN 52612 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volumetric resistance | 1.0E+14 | Ω.cm | IEC 60093 |
| Surface resistance | 1.0E+14 | Ω.cm | IEC 60093 |
| Insulation strength | |||
| 1.50 mm | 22 | KV/mm | IEC 60243-1 |
| Dielectric constant | |||
| 23℃ | 3.40 | 1 MHz | IEC 60250 |
| 23℃ | 3.60 | 100 Hz | IEC 60250 |
| Dissipation factor | |||
| 23℃ | 0.021 | 1 MHz | IEC 60250 |
| 23℃ | 3.1E-3 | 100 Hz | IEC 60250 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| All color | 1.50mm | HB | UL-94 |
| All color | 0.71mm | HB | UL-94 |
| All color | 3.00mm | HB | UL-94 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Unnotch Impact strength | |||
| 23℃ | 37 | kJ/m² | ISO 179/1eU |
| -30℃ | 24 | kJ/m² | ISO 179/1eU |
| Charpy Notched Impact Strength | |||
| 23℃ | 4.0 | kJ/m² | ISO 179/1eA |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 70-100 | °C | |
| Drying time | 2.0-6.0 | Hr | |
| Recommended moisture content | <=0.20 | % | |
| Barrel rear temperature | 210-240 | °C | |
| Barrel middle temperature | 220-250 | °C | |
| Barrel front temperature | 230-260 | °C | |
| Nozzle temperature | 240-270 | °C | |
| Mold temperature | 50-100 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. solution 0,005 g/ml Phenole/1,2 Dichlorbenzol 1:1 |
| 3. plate with film gate 150*150*3 mm³ |
| 4. strain <= 0,5%, 23°C |
| 5. 20000 h |
| 6. 5000 h |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |