| About |
|---|
| Ultradur S 4090 G6 LS High Speed Black is a fast cycling low warpage, 30% glass filled injection molding PBT + ASA blend.&& |
| Product Description | |
|---|---|
| Supplier | BASF |
| Generic | PBT+ASA |
| Material Status | Commercial: Active |
| Features | Low warping,Quick molding cycle |
| Availabilitys | North America |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.47 | g/cm³ | ISO 1183 |
| Melt Flow Rate | |||
| 275℃，2.16kg | 33.90 | g/10min | ISO 1133 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 215 | ℃ | ISO 75-2/Bf |
| 1.8 MPa, annealed | 190 | ℃ | ISO 75-2/Af |
| Melting temperature | 223 | ℃ | ISO 11357-3 |
| Vicat Softening Temp |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Dielectric constant | |||
| 23℃ | 3.80 | 100 Hz | IEC 60250 |
| 23℃ | 3.70 | 1 MHz | IEC 60250 |
| Dissipation factor | |||
| 23℃ | 3.0E-3 | 100 Hz | IEC 60250 |
| 23℃ | 0.018 | 1 MHz | IEC 60250 |
| Compared to the leakage tracing index | 325 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.60 mm | UL 94 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Ball hardness | 140 | MPa | ISO 2039-1 |
| tensile strength | |||
| 23℃ | 125 | MPa | ISO 527-2 |
| Tensile strain | |||
| Fracture, 23 ℃ | 2.1 | % | ISO 527-2 |
| Tensile modulus | |||
| 23℃ | 9900 | MPa | ISO 527-2 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Extrusion molding conditions | Nominal value | Unit | Test method |
| Drying temperature | 80 -120 | °C | |
| Drying time | 4.0 | Hr | |
| Water content | 0.040 | % | |
| Injection temperature | |||
| Rear barrel temperature | 260-260 | °C | |
| Central temperature of the barrel | 265-265 | °C | |
| Barrel front temperature | 270-270 | °C | |
| Die temperature | 270-270 | °C | |
| Mold temperature | 60-100 | °C | |
| Drying temperature | 80-80 | °C | |
| Drying time | 2.0-4.0 | Hr | |
| Zone 1 temperature | 245-260 | °C | |
| Zone 3 temperature | 240-255 | °C | |
| Zone 5 temperature | 240-250 | °C | |
| Die temperature | 225-240 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |