| About |
|---|
| Product Description | |
|---|---|
| Supplier | BASF |
| Generic | POM |
| Material Status | Commercial: Active |
| Features | Fast Cure,Good liquidity |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.41 | g/cm³ | ISO 1183 |
| Molding shrinkage | |||
| Parallel | 2 | % | ISO 294-4 |
| Vertical normal | 2.1 | % | ISO 294-4 |
| Moisture Absorption | |||
| 50% r.h. | 0.2 | % | ISO 62 |
| Saturation | 0.8 | % | ISO 62 |
| Melt Volume Rate | |||
| 190℃，2.16kg | 25 | ccm/10min | ISO 1133 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile Modulus | 2850 | MPa | ISO 527 |
| Tensile Stress | |||
| Yield yld | 65 | MPa | ISO 527 |
| Tensile Strain | |||
| Yield yld | 8 | % | ISO 527 |
| Broken BRK | 24 | % | ISO 527 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Izod Notched Impact strength | |||
| -30℃ | 5 | KJ/m² | ISO 180/1A |
| 23℃ | 5 | KJ/m² | ISO 180/1A |
| Charpy Notched Impact Strength | |||
| -30℃ | 4 | kJ/m² | ISO 179 |
| 23℃ | 4.5 | kJ/m² | ISO 179 |
| Charpy Unnotch Impact strength | |||
| -30℃ | 190 | kJ/m² | ISO 179 |
| 23℃ | 190 | kJ/m² | ISO 179 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Melting point | 166 | ℃ | ISO 3146 |
| Hot deformation temperature HDT | 100 | ℃ | ISO 75-1/-2 |
| Coeff. of linear thermal expansion | 1.1 | ×10-4/℃ |
| ELECTRICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Compared Tracking Index | 600 | IEC 60112 | |
| Volume Resistance | 1E11 | ohm·m | IEC 60093 |
| Surface Resistivity | 1E13 | ohm | IEC 60093 |
| Dielectric Constant | 3.8 | 1 MHZ | IEC 60250 |
| Dissipation Factor | 50 | 1 MHz | IEC 60250 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame Class Rating | |||
| 0.75 mm | HB | UL 94 | |
| 1.5 mm | HB | UL 94 | |
| 3.0 mm | HB | UL 94 | |
| Glow Wire Flammability Index (GWFI) | |||
| Electrical | |||
| 0.75 mm | 105 | ℃ | UL746B |
| 1.5 mm | 105 | ℃ | UL746B |
| 3.0 mm | 105 | ℃ | UL746B |
| Mechanical w/Impact | |||
| 1.5 mm | 90 | ℃ | UL746B |
| 3.0 mm | 90 | ℃ | UL746B |
| Non mechanical w/o Impact | |||
| 1.5 mm | 90 | ℃ | UL746B |
| 3.0 mm | 105 | ℃ | UL746B |
| Process Conditions | |||
|---|---|---|---|
| Injection Molding | Nominal value | Unit | Test method |
| Drying Temperature | 80-110 | ℃ | |
| Drying Time | 2-4 | hr | |
| Maximum Moisture Content | 0.15 | % | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |