| About |
|---|
| A Glass fibre reinforced injection moulding grade for industrial parts requiring high rigidity and providing electrical insulation.&& |
| Product Description | |
|---|---|
| Supplier | BASF |
| Generic | PA66 |
| Material Status | Commercial: Active |
| Features | Grease resistance,Good Rigidity |
| Availabilitys | Europe,Asia Pacific |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.56 | g/cm³ | ISO 1183 |
| viscosity | |||
| 5%，96%H2SO4 | 130 | cm³/g | ISO 307，1157，1628 |
| Water absorption rate | |||
| Equilibrium, 23 ℃, 50% RH | 1.0-1.4 | % | ISO 62 |
| Saturation, 23 ℃ | 3.7-4.3 | % | ISO 62 |
| Halogen content (Cl, Br, I) | <100 | mg/kg | Schoeniger IC |
| Melting temperature, DSC | 260 | °C | ISO 11357-1/-3 |
| Melt Volume Rate | |||
| 275°C，5kg | 8 | cm³/10min | ISO 1133 |
| Shrinkage rate | |||
| MD | 0.82 | % | ISO 294-4 |
| TD | 0.33 | % | ISO 294-4 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 16800/12500 | MPa | ISO 527-1-2 |
| Tensile strain | 240/180 | MPa | ISO 527-1-2 |
| Tensile fracture | 2.5/3.5 | % | ISO 527-1/-2 |
| Bending modulus | 15000/13500 | MPa | ISO 178 |
| bending strength | 360/300 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Unnotch Impact strength | |||
| 23℃ | 95/100 | kJ/m² | ISO 179/1eU |
| -30℃ | 90/- | kJ/m² | ISO 179/1eU |
| Charpy Notched Impact Strength | |||
| 23℃ | 18/25 | kJ/m² | ISO 179/1eA |
| -30℃ | 13/- | kJ/m² | ISO 179/1eA |
| Impact strength of cantilever beam notch | |||
| 23℃ | 13/14.5 | kJ/m² | ISO 180-1eA |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa | 250 | ℃ | ISO 75-1/2 |
| 0.45 MPa | 260 | ℃ | ISO 75-1/2 |
| Maximum operating temperature (short cycle operation) | 240 | °C | – |
| Linear coefficient of thermal expansion | |||
| MD：23~80℃ | 5-20 | E-6/K | ISO 11359-1/-2 |
| TD：23~80℃ | 50-60 | E-6/K | ISO 11359-1/-2 |
| Thermal conductivity | 0.37 | W/(m K) | DIN 52612-1 |
| Specific heat capacity | 1300 | J/(kg*K) |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Relative permittivity | 3.8 / 6.6 | IEC 60250 | |
| Dissipation coefficient (1MHz) | 150 / 1700 | E-4 | IEC 60250 |
| Volume resistivity | 1E+15 | ohms·cm | IEC 60093 |
| Surface resistivity | 1E+10 | ohms | IEC 60093 |
| Compared to the leakage tracing index | |||
| Solution A | 550 | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.6mm | HB | IEC 60695-11-10 |
| Process Conditions | |||
|---|---|---|---|
| Injection molding and extrusion processing | Nominal value | Unit | Test method |
| Melt Temperature | 280-310 | ℃ | |
| Mold temperature | 80-90 | ℃ | |
| Mold shrinkage | 0.46 | % | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Test box with central gating, dimensions of base (107*47*1,5) mm, processing conditions: TM = 290°C, TW = 80°C |
| 3. strain <= 0.5%, 23°C |
| 4. 5000 h |
| 5. 20000 h |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |