| About |
|---|
| 冲击改性和稳定注塑成型，抗低温冲击性 |
| Product Description | |
|---|---|
| Supplier | BASF |
| Generic | PA66 |
| Material Status | Commercial: Active |
| Features | High impact resistance,Grease resistance,low-temperature impact resistance |
| Availabilitys | Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.06 | g/cm³ | ISO 1183 |
| 表观密度 | 0.70 | g/cm³ | |
| Melt Volume Rate | |||
| 275℃，10 kg | 38.0 | cm³/10min | ISO 1133 |
| Water absorption rate | |||
| Saturation, 23 ℃ | 6.7 to 7.7 | % | ISO 62 |
| Equilibrium, 23 ℃, 50% RH | 2.0 to 2.6 | % | ISO 62 |
| Shrinkage rate | 0.85 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 1900 | MPa | ISO 527-2 |
| tensile strength | |||
| yield | 48.0 | MPa | ISO 527-2/50 |
| Tensile strain | |||
| yield | 5.0 | % | ISO 527-2/50 |
| Nominal tensile fracture strain | 45 | % | ISO 527-2/50 |
| Tensile creep modulus | 450 | MPa | ISO 899-1 |
| Bending modulus | 1750 | MPa | ISO 178 |
| bending strength | 64.0 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| -30℃ | 31 | kJ/m² | ISO 179/1eA |
| 23℃ | 90 | kJ/m² | ISO 179/1eA |
| Charpy Unnotch Impact strength | |||
| 23℃ | 无断裂 | ISO 179/1eU | |
| Impact strength of cantilever beam notch | |||
| -30℃ | 29 | kJ/m² | ISO 180-A |
| 23℃ | 90 | kJ/m² | ISO 180-A |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 125 | ISO 75-2/B | |
| 1.8 MPa, unannealed | 60.0 | ISO 75-2/A | |
| Melting temperature | 260 | ISO 11357-3 | |
| Linear coefficient of thermal expansion | |||
| MD：23~80℃ | 7.0E-5 to 1.0E-4 | ISO 11359-2 | |
| specific heat | 1700 | ||
| Thermal conductivity coefficient | 0.33 | DIN 52612 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | 1.0E+12 | ohms | IEC 60093 |
| Volume resistivity | 4.0E+14 | IEC 60093 | |
| Relative permittivity | |||
| 1 MHz | 3.10 | IEC 60250 | |
| Dissipation factor | |||
| 1 MHz | 0.016 | IEC 60250 | |
| Compared to the leakage tracing index | |||
| Solution A | 600 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 1.60 mm | HB | UL 94 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 80 | °C | |
| Drying time | 4.0 | hr | |
| Recommended maximum moisture content | 0.15 | % | |
| Hopper temperature | 80 | °C | |
| Barrel rear temperature | 290 | °C | |
| Barrel middle temperature | 290 | °C | |
| Barrel front temperature | 290 | °C | |
| Nozzle temperature | 290 | °C | |
| Processing (melt) temperature | 280 to 300 | °C | |
| Mold temperature | 60 to 80 | °C | |
| residence time | < 10.0 | min | |
| Screw speed | < 300 | mm/sec | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |