| About |
|---|
| Ultramid A3ZM2 BK30564 is a specially formulated, non-conductive polyamide based engineering resin for off-line paint applications. The A3ZM2 BK30564 is designed to provide high thermal and chemical resistance, predictable dimensional stability, thin wall processing and a Class A surface. Applications Typical applications include automotive mirror shells and fuel doors and automotive and industrial panels.&& |
| Product Description | |
|---|---|
| Supplier | BASF |
| Generic | PA66 |
| Material Status | Commercial: Active |
| Features | Good Dimensional Stability,Sprayable,High Heat Resistance,Grease resistance,Solvent resistance |
| Availabilitys | North America |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.15 | g/cm³ | ISO 1183 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| 23℃ | 2850 | MPa | ISO 527-2 |
| tensile strength | |||
| Fracture, 23 ℃ | 49.0 | MPa | ISO 527-2 |
| Yield, 23 ℃ | 51.0 | MPa | ISO 527-2 |
| Tensile strain | |||
| Fracture, 23 ℃ | 15 | % | ISO 527-2 |
| Yield, 23 ℃ | 4.1 | % | ISO 527-2 |
| Bending modulus | |||
| 23℃ | 2880 | MPa | ISO 178 |
| bending strength | |||
| 23℃ | 86.0 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179 | ||
| -30℃ | 5.4 | kJ/m² | ISO 179 |
| 23℃ | 8.5 | kJ/m² | ISO 179 |
| Charpy Unnotch Impact strength | ISO 179 | ||
| -30℃ | 130 | kJ/m² | ISO 179 |
| 23℃ | 160 | kJ/m² | ISO 179 |
| Impact strength of cantilever beam notch | ISO 180 | ||
| -40℃ | 5.5 | kJ/m² | ISO 180 |
| 23℃ | 8.1 | kJ/m² | ISO 180 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 77.0 | ℃ | ISO 75-2/A |
| 0.45 MPa, unannealed | 192 | ℃ | ISO 75-2/B |
| Melting temperature | |||
| DSC | 260 | ℃ | ISO 3146 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 80 | °C | |
| Drying time | 2.0 to 4.0 | hr | |
| Recommended maximum moisture content | 0.15 | % | |
| Processing (melt) temperature | 280 to 305 | °C | |
| Mold temperature | 80 to 90 | °C | |
| Injection pressure | 3.50 to 12.5 | MPa | |
| Injection speed | Fast | ||
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |