UmaPET HQO/HQI

About
KEY FEATURES Uma PET HQ is transparent film with one side co-extruded layer of specially modified copolymer. HQ film possesses low Haze, high clarity, high gloss along with good frictional, mechanical and thermal properties. The Film can be used for direct contact with food and complies with FDA regulation 21CFR177.1630 sections (f) and (g). APPLICATIONS The modified co-extruded surface has excellent adhesion with water and solvent based inks, adhesives, release coatings, Varnishes, primers and Al-metals in metallization, resulted higher bond strength in final laminates. Laminates with HQ film shows excellent inter layer bond strength retention in high end packaging applications like hot fill, boiling, retorting etc. Boil in Bag, Doy-Pack type of packaging applications for various products.&&

About

KEY FEATURES Uma PET HQ is transparent film with one side co-extruded layer of specially modified copolymer. HQ film possesses low Haze, high clarity, high gloss along with good frictional, mechanical and thermal properties. The Film can be used for direct contact with food and complies with FDA regulation 21CFR177.1630 sections (f) and (g). APPLICATIONS The modified co-extruded surface has excellent adhesion with water and solvent based inks, adhesives, release coatings, Varnishes, primers and Al-metals in metallization, resulted higher bond strength in final laminates. Laminates with HQ film shows excellent inter layer bond strength retention in high end packaging applications like hot fill, boiling, retorting etc. Boil in Bag, Doy-Pack type of packaging applications for various products.&&

Product Description
Generic	PET
Material Status	Commercial: Active
Features	Good Rigidity,Good Clarity,Good surface appearance,Low coefficient of friction,Food contact compliance,Agglomerability,Resistance to salt water/fog
Availabilitys	Africa & Middle East ,Europe

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Shrinkage rate			ASTM D1204
MD：150℃，0.012 mm，30 min	2.5	%
TD：150℃，0.012 mm，30 min	0.40	%

MECHANICAL	Nominal value	Test method
friction coefficient		ASTM D1894
With oneself – dynamic	0.45
With oneself – static	0.50

film	Nominal value	Unit	Test method
film thickness
test	12	µm
film thickness	12 µm
tensile strength			ASTM D882
MD, fracture, 12 µ m	206	MPa
TD, fracture, 12 µ m	216	MPa
Tensile strain			ASTM D882
MD, fracture, 12 µ m	100	%
TD, fracture, 12 µ m	90	%
dosage
12.0 µm	59.5	m²/kg	Internal Method

optical performance	Nominal value	Unit	Test method
Haze
12 µm	3.0	%	ASTM D1003

Supplementary information	Nominal value	Unit	Test method
Wetting Tension			ASTM D2578
Functional side：12.0 µm	42	dyne/cm
Plain side：12.0 µm	44	dyne/cm

Notes
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.