| About |
|---|
| UNITIKA Nylon 6 A1030GFL45 is a Polyamide 6 (Nylon 6) material filled with 45% glass fiber. It is available in Asia Pacific or North America. Primary attribute of UNITIKA Nylon 6 A1030GFL45: Flame Rated. Typical applications include: Automotive Construction Applications Housings&& |
| Product Description | |
|---|---|
| Supplier | UNITIKA |
| Generic | PA6 |
| Material Status | Commercial: Active |
| Features | HB |
| Availabilitys | North America,Asia Pacific |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.50 | g/cm³ | ISO 1183 |
| Shrinkage rate | ISO 294-4 | ||
| TD：3.2 mm | 0.30 | % | ISO 294-4 |
| MD：3.2 mm | 0.10 | % | ISO 294-4 |
| Water absorption rate | ISO 62 | ||
| 23℃，24hr | 1.0 | % | ISO 62 |
| Equilibrium, 23 ℃, 50% RH | 1.5 | % | ISO 62 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | 15 | kJ/m² | ISO 179 |
| Charpy Unnotch Impact strength | 79 | kJ/m² | ISO 179 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 217 | ℃ | ISO 75-2/B |
| 1.8 MPa, unannealed | 204 | ℃ | ISO 75-2/A |
| Linear coefficient of thermal expansion | |||
| MD | 2.3E-5 | 1/℃ | ISO 11359-2 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 2.0E+15 | ohms·cm | IEC 60093 |
| Dielectric strength | |||
| 1 mm | 42 | kV/mm | IEC 60243-1 |
| Dielectric constant | |||
| 1 MHz | 3.30 | IEC 60250 | |
| Dissipation factor | |||
| 1 MHz | 0.022 | IEC 60250 | |
| Compared to the leakage tracing index | 550 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 0.90 mm | HB | UL 94 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | |||
| R-level | 122 | ISO 2039-2 | |
| Tensile modulus | 13600 | MPa | ISO 527-2 |
| tensile strength | |||
| fracture | 210 | MPa | ISO 527-2 |
| Tensile strain | |||
| fracture | 2.9 | % | ISO 527-2 |
| Bending modulus | 12400 | MPa | ISO 178 |
| bending strength | 325 | MPa | ISO 178 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |