| About |
|---|
| Urea- formaldehyde resins fortified with highly refined cellulose as filler, and further modified with minor amounts of special purpose additives, pigments, cure regulators and lubricants. The Urochem 162 Moulding Compounds can be supplied in an almost unlimited range of colours from translucent light pastels to black. Moulded parts are free from odour; UV stable with good moisture resistance. Hard, glossy and scratch resistant surface. Excellent chemical resistance. Fats, oils and common organic solvents like alcohol and acetone do not attack moulded parts which are also resistant to surfactants and weak bases. They will withstand attack from weak acids for a shorter duration. Excellent electrical properties (arc quenching, tracking, flame resistance). Oxygen index of 30% is achieved without the use of external flame retardants. No halogens are present in the composition. Compliant with the requirements of widely used material specificationsfor amino compounds: BS 1322 type UF A10 (*) DIN 7708 type 131.5 (*) ISO 2112 type UF A10 (*) UL certified (*) included in ISO 14527 Fields of application: The Urochem 162 Urea Moulding Compound has low shrinkage, low water absorption and high strength. It is suitable for electrical accessories (typically faceplates).&& |
| Product Description | |
|---|---|
| Generic | 脲醛树脂 |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Weather resistance is good,Alkali resistant,Good surface appearance,Good Electrical Properties,Renewable resources,Low or no water absorption,Ethanol tolerance,Good Hardness,Low contractility,Halogen free,Low odor,Moisture resistance,Lubricating,Grease resistance,Solvent resistance,High scratch resistance,V-0 |
| Availabilitys | North America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.50 | g/cm³ | ISO 1183 |
| Shrinkage rate | ISO 2577 | ||
| — | 0.60 to 0.80 | % | ISO 2577 |
| — | 0.70 to 1.0 | % | ISO 2577 |
| Water absorption rate | < 300.0 | mg | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| yield | > 45.0 | MPa | ISO 527-2 |
| bending strength | > 80.0 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | > 1.1 | kJ/m² | ISO 179-1eA |
| Charpy Unnotch Impact strength | > 5.0 | kJ/m² | ISO 179/1eU |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 8.0 MPa, unannealed | > 90.0 | ℃ | ISO 75-2/C |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | > 1.0E+11 | ohms | IEC 60093 |
| Volume resistivity | > 1.1E+11 | ohms·cm | IEC 60093 |
| Dielectric constant | 5.00 | DIN 53483 | |
| Dissipation factor | |||
| 1 kHz | < 0.10 | IEC 60250 | |
| Compared to the leakage tracing index | < 600 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | V-0 | UL 94 | |
| Glowing wire flammability index | 960 | ℃ | IEC 707 |
| Extreme oxygen index | > 30 | % | ASTM D2863 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Post-shrink |
| 3. 180 sec |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |