| About |
|---|
| VALOX 310SE0 is an unreinforced, flame retardant PBT injection moulding resin. Applications: electrical industry, bobbins, keyboard, switches and switch components and appliance housings.&& |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | polybutylene terephthalate |
| Material Status | Commercial: Active |
| Features | Flame Characteristics,V-0,5VA |
| Availabilitys | North America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.40 | g/cm³ | ASTM D792 |
| Specific volume | 0.710 | cm³/g | ASTM D792 |
| Density | 1.40 | g/cm³ | ISO 1183 |
| Melt Flow Rate | |||
| 250℃，2.16kg | 8.6 | g/10min | ASTM D1238 |
| Melt Volume Rate | |||
| 250℃，2.16 kg | 8.00 | cm³/10min | ISO 1133 |
| Shrinkage rate | Internal Method | ||
| MD | 1.1 to 1.8 | % | Internal Method |
| MD | 1.5 to 2.3 | % | Internal Method |
| MD | 0.90 to 1.6 | % | Internal Method |
| MD：3.2 mm | 1.5 to 2.3 | % | Internal Method |
| Water absorption rate | |||
| Saturation, 23 ℃ | 0.36 | % | ISO 62 |
| Equilibrium, 23 ℃, 50% RH | 0.080 | % | ISO 62 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| -30℃ | 4.0 | kJ/m² | ISO 179/1eA |
| 23℃ | 8.0 | kJ/m² | ISO 179/1eA |
| 23℃ | 4.0 | kJ/m² | ISO 179/2C |
| Charpy Unnotch Impact strength | ISO 179/1eU | ||
| -30℃ | No Break | ISO 179/1eU | |
| 23℃ | No Break | ISO 179/1eU | |
| Impact strength of cantilever beam notch | ASTM D256 | ||
| -30℃ | 22 | J/m | ASTM D256 |
| 23℃ | 37 | J/m | ASTM D256 |
| Impact strength of cantilever beam notch | ISO 180/1A | ||
| 23℃ | 1600 | J/m | ASTM D4812 |
| -30℃ | 3.0 | kJ/m² | ISO 180-1A |
| 23℃ | 5.0 | kJ/m² | ISO 180-1A |
| Notched impact strength of cantilever beam | ISO 180/1U | ||
| -30℃ | No Break | ISO 180/1U | |
| 23℃ | No Break | ISO 180/1U | |
| Dart impact equipped with measuring instruments | |||
| 23℃，Total Energy | 200 | J | ASTM D3763 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | ASTM D648 | ||
| 0.45 MPa, unannealed, 6.4 mm | 162 | ℃ | ASTM D648 |
| 0.45 MPa, unannealed, 100 mm span | 135 | ℃ | ISO 75-2/Be |
| 1.8 MPa, unannealed, 3.2 mm | 74.0 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed, 6.4 mm | 71.0 | ℃ | ASTM D648 |
| Hot deformation temperature | |||
| 1.8 MPa, unannealed, 100 mm span | 60.0 | ℃ | ISO 75-2/Ae |
| 1.8 MPa, unannealed, 64 mm span | 71.0 | ℃ | ISO 75-2/Af |
| Vicat Softening Temp | 165 | ℃ | ASTM D1525 14 |
| Vicat Softening Temp | |||
| A50 | 212 | ℃ | ISO 306/A50 |
| B50 | 165 | ℃ | ISO 306 |
| B120 | 165 | ℃ | ISO 306/B120 |
| Ball pressure test | |||
| 125℃ | Pass | IEC 60695-10-2 | |
| Linear coefficient of thermal expansion | |||
| TD：-40~40℃ | 7.9E-5 | 1/℃ | ASTM E831 |
| TD | ISO 11359-2 | ||
| -40 to 40 ℃ | 7.3E-5 | cm/cm/℃ | ISO 11359-2 |
| MD | ASTM E831 | ||
| -40 to 40 ℃ | 7.9E-5 | cm/cm/℃ | ASTM E831 |
| 60 to 138 ℃ | 1.3E-4 | cm/cm/℃ | ASTM E831 |
| MD | ISO 11359-2 | ||
| -40 to 40 ℃ | 7.6E-5 | cm/cm/℃ | ISO 11359-2 |
| 23 to 60 ℃ | 1.0E-4 | cm/cm/℃ | ISO 11359-2 |
| Thermal conductivity coefficient | 0.24 | W/m/K | ISO 8302 |
| Relative temperature index | |||
| Electrical performance | 120 | ℃ | UL 746 |
| Strength mechanical performance | 140 | ℃ | UL 746 |
| Impact mechanical performance | 120 | ℃ | UL 746 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | > 1.0E+15 | ohms | IEC 60093 |
| Volume resistivity | > 1.0E+15 | ohms·cm | IEC 60093 |
| Dielectric strength | ASTM D149 | ||
| 1.6 mm in oil | 22 | kV/mm | ASTM D149 |
| 3.2 mm in air | 18 | kV/mm | ASTM D149 |
| Dielectric strength | IEC 60243-1 | ||
| 0.8 mm in oil | 31 | kV/mm | IEC 60243-1 |
| 1 mm | 18 | kV/mm | IEC 60243-1 |
| 1.6 mm in oil | 24 | kV/mm | IEC 60243-1 |
| 3.2 mm in oil | 15 | kV/mm | IEC 60243-1 |
| Relative permittivity | IEC 60250 | ||
| 50 Hz | 2.90 | IEC 60250 | |
| 60 Hz | 2.90 | IEC 60250 | |
| 100 Hz | 3.10 | IEC 60250 | |
| 1 MHz | 2.80 | IEC 60250 | |
| Dissipation factor | IEC 60250 | ||
| 50 Hz | 1.0E-3 | IEC 60250 | |
| 60 Hz | 1.0E-3 | IEC 60250 | |
| 100 Hz | 2.0E-3 | IEC 60250 | |
| 1 MHz | 0.010 | IEC 60250 | |
| Arc resistance | PLC 6 | ASTM D495 | |
| Compared to the leakage tracing index | PLC 3 | UL 746 | |
| Compared to the leakage tracing index | IEC 60112 | ||
| CTI | 175 | V | IEC 60112 |
| Solution B | 100 | V | IEC 60112 |
| High Arc Burning Index (HAI) | PLC 0 | UL 746 | |
| High voltage arc ignition resistance index (HVAR) (PLC) | PLC 6 | UL 746 | |
| High voltage arc marking rate | |||
| HVTR | PLC 4 | UL 746 | |
| Hot wire ignition | |||
| HWI | PLC 2 | UL 746 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | UL 94 | ||
| 0.71 mm | V-0 | UL 94 | |
| 3.00 mm | 5VA | UL 94 | |
| Glowing wire flammability index | |||
| 1.0 mm | 960 | ℃ | IEC 60695-2-12 |
| Extreme oxygen index | 30 | % | ISO 4589-2 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 2820 | MPa | ASTM D638 |
| Tensile modulus | 2800 | MPa | ISO 527-1-2 |
| tensile strength | |||
| fracture | 40.0 | MPa | ISO 527-2/50 |
| fracture | 58.0 | MPa | ASTM D638 |
| yield | 58.0 | MPa | ASTM D638 |
| yield | 55.0 | MPa | ISO 527-2/50 |
| Tensile strain | |||
| fracture | 20 | % | ASTM D638 |
| fracture | 20 | % | ISO 527-2/50 |
| yield | 20 | % | ASTM D638 |
| yield | 6.0 | % | ISO 527-2/50 |
| Bending modulus | 2600 | MPa | ISO 178 |
| 50 mm span | 2620 | MPa | ASTM D790 |
| bending strength | 90.0 | MPa | ISO 178 |
| bending strength | |||
| Yield, 50 mm span | 101 | MPa | ASTM D790 |
| Taber abraser | |||
| 1000 cycles, 1000 g, CS-17 wheels | 19.0 | mg | Internal Method |
| Rockwell hardness | |||
| R-level | 120 | ISO 2039-2 | |
| Ball hardness | |||
| H358/30 | 105 | MPa | ISO 2039-1 |
| Special value | Nominal value | Unit | Test method |
|---|---|---|---|
| TD | 0.90 to 1.9 | % | Internal Method |
| TD | 1.0 to 1.7 | % | Internal Method |
| TD | 1.6 to 2.4 | % | Internal Method |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 121 | °C | |
| Drying time | 3.0 to 4.0 | hr | |
| Drying time, maximum | 12 | hr | |
| Recommended maximum moisture content | 0.020 | % | |
| Recommended injection volume | 40 to 80 | % | |
| Barrel rear temperature | 232 to 249 | °C | |
| Barrel middle temperature | 238 to 254 | °C | |
| Barrel front temperature | 243 to 260 | °C | |
| Nozzle temperature | 238 to 254 | °C | |
| Processing (melt) temperature | 243 to 260 | °C | |
| Mold temperature | 49 to 77 | °C | |
| Back pressure | 0.345 to 0.689 | MPa | |
| Screw speed | 50 to 100 | rpm | |
| Vent depth | 0.013 to 0.025 | mm | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Tensile Bar |
| 3. 0.20 in/min |
| 4. Type I, 2.0 in/min |
| 5. 0.051 in/min |
| 6. 0.079 in/min |
| 7. at Yield |
| 8. 80*10*4 sp=62mm |
| 9. 80*10*4 mm |
| 10. 120*10*4 mm |
| 11. Rate A (50°C/h), Loading 2 (50 N) |
| 12. Shorttime |
| 13. Tungsten Electrode |
| 14. Surface |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |