| About |
|---|
| 30% GR, excellent strength, stiffness and dimensional stability. High heat resistance. Appliance handles, spotlights, electric motors, connectors.&& |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | polybutylene terephthalate |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Good Dimensional Stability,High Heat Resistance,HB |
| Availabilitys | North America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.53 | g/cm³ | ASTM D792 |
| Specific volume | 0.660 | cm³/g | ASTM D792 |
| Melt Flow Rate | |||
| 250℃，2.16kg | 17 | g/10min | ISO 1133 |
| Melt Volume Rate | |||
| 250℃，2.16 kg | 13.0 | cm³/10min | ISO 1133 |
| Shrinkage rate | Internal Method | ||
| MD | 0.30 to 0.70 | % | Internal Method |
| MD | 0.30 to 0.50 | % | Internal Method |
| MD | 0.50 to 0.80 | % | Internal Method |
| MD：3.2 mm | 0.30 to 0.80 | % | Internal Method |
| Water absorption rate | |||
| Equilibrium, 23 ℃, 50% RH | 0.080 | % | ISO 62 |
| 24hr | 0.090 | % | ASTM D570 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179/1eA | ||
| -30℃ | 5.0 | kJ/m² | ISO 179/1eA |
| 23℃ | 5.0 | kJ/m² | ISO 179/1eA |
| Charpy Unnotch Impact strength | ISO 179/1eU | ||
| -30℃ | 45 | kJ/m² | ISO 179/1eU |
| 23℃ | 45 | kJ/m² | ISO 179/1eU |
| Impact strength of cantilever beam notch | ASTM D256 | ||
| 23℃ | 800 | J/m | ASTM D4812 |
| -30℃ | 80 | J/m | ASTM D256 |
| 23℃ | 85 | J/m | ASTM D256 |
| Impact strength of cantilever beam notch | ISO 180/1A | ||
| -30℃ | 7.0 | kJ/m² | ISO 180-1A |
| 23℃ | 8.0 | kJ/m² | ISO 180-1A |
| Notched impact strength of cantilever beam | ISO 180/1U | ||
| -30℃ | 45 | kJ/m² | ISO 180/1U |
| 23℃ | 45 | kJ/m² | ISO 180/1U |
| Dart impact equipped with measuring instruments | |||
| 23℃，Total Energy | 8.00 | J | ASTM D3763 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | ASTM D648 | ||
| 1.8 MPa, unannealed, 64 mm span | 204 | ℃ | ISO 75-2/Af |
| 0.45 MPa, unannealed, 64 mm span | 217 | ℃ | ISO 75-2/Bf |
| 1.8 MPa, unannealed, 3.2 mm | 203 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed, 6.4 mm | 207 | ℃ | ASTM D648 |
| Vicat Softening Temp | 215 | ℃ | ASTM D1525 14 |
| Vicat Softening Temp | |||
| A50 | 223 | ℃ | ISO 306/A50 |
| B50 | 215 | ℃ | ISO 306 |
| B120 | 215 | ℃ | ISO 306/B120 |
| Ball pressure test | |||
| 125℃ | Pass | IEC 60695-10-2 | |
| Linear coefficient of thermal expansion | |||
| TD：-40~40℃ | 1.2E-4 | 1/℃ | ASTM E831 |
| TD：-40~40℃ | 1.2E-4 | 1/℃ | ISO 11359-2 |
| MD：-40~40℃ | 2.5E-5 | 1/℃ | ISO 11359-2 |
| MD | ASTM E831 | ||
| -40 to 40 ℃ | 2.5E-5 | cm/cm/℃ | ASTM E831 |
| 60 to 138 ℃ | 2.5E-5 | cm/cm/℃ | ASTM E831 |
| Thermal conductivity coefficient | 0.19 | W/m/K | ISO 8302 |
| Relative temperature index | |||
| Electrical performance | 140 | ℃ | UL 746 |
| Strength mechanical performance | 140 | ℃ | UL 746 |
| Impact mechanical performance | 140 | ℃ | UL 746 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | > 1.0E+15 | ohms | IEC 60093 |
| Volume resistivity | > 3.2E+16 | ohms·cm | ASTM D257 |
| Volume resistivity | > 1.0E+15 | ohms·cm | IEC 60093 |
| Dielectric strength | ASTM D149 | ||
| 1.6 mm in oil | 25 | kV/mm | ASTM D149 |
| 3.2 mm in air | 19 | kV/mm | ASTM D149 |
| Dielectric strength | IEC 60243-1 | ||
| 0.8 mm in oil | 28 | kV/mm | IEC 60243-1 |
| 1 mm | 19 | kV/mm | IEC 60243-1 |
| 1.6 mm in oil | 24 | kV/mm | IEC 60243-1 |
| 3.2 mm in oil | 16 | kV/mm | IEC 60243-1 |
| Dielectric constant | ASTM D150 | ||
| 100 Hz | 3.80 | ASTM D150 | |
| 1 MHz | 3.70 | ASTM D150 | |
| Relative permittivity | IEC 60250 | ||
| 50 Hz | 3.10 | IEC 60250 | |
| 60 Hz | 3.10 | IEC 60250 | |
| 1 MHz | 3.10 | IEC 60250 | |
| Dissipation factor | ASTM D150 | ||
| 100 Hz | 2.0E-3 | ASTM D150 | |
| 1 MHz | 0.020 | ASTM D150 | |
| Dissipation factor | IEC 60250 | ||
| 50 Hz | 1.0E-3 | IEC 60250 | |
| 60 Hz | 1.0E-3 | IEC 60250 | |
| 100 Hz | 1.0E-3 | IEC 60250 | |
| 1 MHz | 0.010 | IEC 60250 | |
| Arc resistance | PLC 5 | ASTM D495 | |
| Compared to the leakage tracing index | PLC 0 | UL 746 | |
| Compared to the leakage tracing index | 300 | V | IEC 60112 |
| High voltage arc marking rate | |||
| HVTR | PLC 1 | UL 746 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 0.80 mm | HB | UL 94 | |
| Glowing wire flammability index | |||
| 1.0 mm | 750 | ℃ | IEC 60695-2-12 |
| Extreme oxygen index | 19 | % | ASTM D2863 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Filler | 30 | % | ASTM D229 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 9300 | MPa | ASTM D638 |
| Tensile modulus | 9300 | MPa | ISO 527-1-2 |
| tensile strength | |||
| fracture | 125 | MPa | ISO 527-2/5 |
| fracture | 120 | MPa | ASTM D638 |
| yield | 125 | MPa | ISO 527-2/5 |
| yield | 120 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | 2.7 | % | ASTM D638 |
| fracture | 2.0 | % | ISO 527-2/5 |
| yield | 2.0 | % | ISO 527-2/5 |
| yield | 2.7 | % | ASTM D638 |
| Bending modulus | 8500 | MPa | ISO 178 |
| 50 mm span | 7580 | MPa | ASTM D790 |
| bending strength | 195 | MPa | ISO 178 |
| bending strength | |||
| Fracture, 50 mm span | 190 | MPa | ASTM D790 |
| Yield, 50 mm span | 195 | MPa | ASTM D790 |
| Taber abraser | |||
| 1000 cycles, 1000 g, CS-17 wheels | 19.0 | mg | ASTM D1044 |
| Rockwell hardness | |||
| R-level | 118 | ASTM D785 | |
| R-level | 118 | ISO 2039-2 | |
| Ball hardness | |||
| H358/30 | 122 | MPa | ISO 2039-1 |
| Special value | Nominal value | Unit | Test method |
|---|---|---|---|
| TD | 0.50 to 1.0 | % | Internal Method |
| TD | 0.40 to 0.60 | % | Internal Method |
| TD | 0.60 to 0.90 | % | Internal Method |
| TD：3.2 mm | 0.50 to 1.0 | % | Internal Method |
| 0.45 MPa, unannealed, 3.2 mm | 220 | ℃ | ASTM D648 |
| 0.45 MPa, unannealed, 6.4 mm | 216 | ℃ | ASTM D648 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 121 | °C | |
| Drying time | 3.0 to 4.0 | hr | |
| Drying time, maximum | 12 | hr | |
| Recommended maximum moisture content | 0.020 | % | |
| Recommended injection volume | 40 to 80 | % | |
| Barrel rear temperature | 238 to 254 | °C | |
| Barrel middle temperature | 243 to 260 | °C | |
| Barrel front temperature | 249 to 266 | °C | |
| Nozzle temperature | 243 to 260 | °C | |
| Processing (melt) temperature | 249 to 266 | °C | |
| Mold temperature | 66 to 88 | °C | |
| Back pressure | 0.345 to 0.689 | MPa | |
| Screw speed | 50 to 80 | rpm | |
| Vent depth | 0.025 to 0.038 | mm | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Tensile Bar |
| 3. 1.5 to 3.2 mm |
| 4. 3.2 to 4.6 mm |
| 5. 3.2-4.6 mm |
| 6. 0.20 in/min |
| 7. Type I, 0.20 in/min |
| 8. 0.051 in/min |
| 9. 0.079 in/min |
| 10. Yield |
| 11. 80*10*4 sp=62mm |
| 12. 80*10*4 |
| 13. 80*10*4 mm |
| 14. Rate B (120°C/h), Loading 2 (50 N) |
| 15. Short-Time |
| 16. Tungsten Electrode |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |