| About |
|---|
| VALOX 7062 is Mineral filled PBT injection molding grade.&& |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | PBT+PET |
| Material Status | Commercial: Active |
| Features | HB |
| Availabilitys | Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.81 | g/cm³ | ISO 1183 |
| Melt Volume Rate | |||
| 265℃，1.2 kg | 21.0 | cm³/10min | ISO 1133 |
| Shrinkage rate | |||
| MD：3.2 mm | 1.2 to 1.9 | % | Internal Method |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179/1eA | ||
| -30℃ | 2.0 | kJ/m² | |
| 23℃ | 2.0 | kJ/m² | |
| Impact strength of cantilever beam notch | |||
| -30℃ | 3.0 | J/m | ASTM D256 |
| 23℃ | 3.0 | J/m | ASTM D256 |
| -30℃ | 3.0 | kJ/m² | ISO 180-1A |
| 23℃ | 3.0 | kJ/m² | ISO 180-1A |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed, 3.2 mm | 65.0 | ℃ | ASTM D648 |
| Vicat Softening Temp | |||
| B50 | 175 | ℃ | ASTM D1525, ISO 306/B50, ISO 306/B120 7 |
| B120 | 175 | ℃ | ASTM D1525, ISO 306/B50, ISO 306/B120 7 |
| Ball pressure test | |||
| 125℃ | Pass | IEC 60695-10-2 | |
| Linear coefficient of thermal expansion | ISO 11359-2 | ||
| MD：23~80℃ | 9.0E-5 | 1/℃ | |
| TD：23~80℃ | 9.0E-5 | 1/℃ |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Dielectric constant | ASTM D150 | ||
| 50 Hz | 3.70 | ||
| 60 Hz | 3.70 | ||
| 1 MHz | 3.60 | ||
| Dissipation factor | ASTM D150 | ||
| 50 Hz | 2.0E-3 | ||
| 60 Hz | 2.0E-3 | ||
| 1 MHz | 0.015 | ||
| Compared to the leakage tracing index | 475 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | UL 94 | ||
| 1.50 mm | HB | ||
| 3.00 mm | HB | ||
| Glowing wire flammability index | |||
| 3.2 mm | 650 | ℃ | IEC 60695-2-12 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Ball hardness | |||
| H358/30 | 140 | MPa | ISO 2039-1 |
| Tensile modulus | 4200 | MPa | ISO 527-1-2 |
| tensile strength | |||
| fracture | 60.0 | MPa | ISO 527-2/5 |
| Tensile strain | |||
| fracture | 3.0 | % | ISO 527-2/5 |
| Bending modulus | 3900 | MPa | ISO 178 |
| bending strength | 100 | MPa | ISO 178 |
| Taber abraser | |||
| 1000 cycles, 1000 g, CS-17 wheels | 74.0 | mg | Internal Method |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |