| About |
|---|
| DuPont™ Vamac® G is a terpolymer of ethylene, methylacrylate, and a cure site monomer. It is cured using an amine-based vulcanization system. This gum elastomer includes a small amount of processing aid, and has a nominal specific gravity of 1.03. It has a mild acrylic odor. Use adequate ventilation during storage, mixing, and processing to prevent accumulation of residual vapors. Storage stability is excellent. Vamac® G has excellent high-temperature durability and oil resistance with service lubricants, coupled with good low-temperature flexibility. Compounds of Vamac® G are typically rated at 175°C (347°F) for heat resistance, with oil swell values around 50% in IRM 903 oil. The properties of Vamac® G make it well suited for a wide range of automotive applications, including powertrain seals and gaskets, rocker cover and piston seals, oil coolant hoses, power steering hoses, turbocharger hoses, crankcase ventilating tubes, coverings for fuel and coolant hoses, O-rings, grommets and spark plug boots. Vamac® G is an excellent vibration damping material that is uniquely insensitive to temperature over a range of -30°C (-22°F) to 160°C (320°F). Compounds of Vamac® G are suitable for use in torsional dampers and isolator pads. Vamac® G is a halogen-free polymer and does not decompose to give off corrosive gasses when exposed to flame. It is used for flame-retarded, low-smoke, nonhalogen wire and cable jackets and in nonhalogen, low-smoke flooring. Vamac® G is well suited for injection, transfer and compression molding, and is easily extruded.&& |
| Product Description | |
|---|---|
| Supplier | DuPont |
| Generic | AEM |
| Material Status | Commercial: Active |
| Features | No viscosity,Low smoke,noise reduction,Halogen free,Flame Characteristics,Low toxicity,High Heat Resistance,Low temperature toughness,Durability,Grease resistance |
| Availabilitys | North America,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Mooney viscosity | ASTM D1646 | ||
| ML 1+4，100℃ | 17 to 40 | MU | ASTM D1646 |
| MS 1，121℃ | > 16 | MU | ASTM D1646 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | ASTM D2240 | ||
| Shaw’s A | 68 | ASTM D2240 | |
| Shaw’s A | 77 | ASTM D2240 | |
| Shaw’s A | 66 | ASTM D2240 | |
| Shaw’s A | 48 | ASTM D2240 | |
| Shaw’s A | 58 | ASTM D2240 | |
| Shaw’s A | 57 | ASTM D2240 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| 100% strain | 5.10 | MPa | ASTM D412 |
| 100% strain | 6.40 | MPa | ASTM D412 |
| 100% strain | 4.70 | MPa | ASTM D412 |
| 100% strain | 4.80 | MPa | ASTM D412 |
| 100% strain | 5.20 | MPa | ASTM D412 |
| tensile strength | ASTM D412 | ||
| yield | 16.6 | MPa | ASTM D412 |
| yield | 15.3 | MPa | ASTM D412 |
| yield | 14.1 | MPa | ASTM D412 |
| yield | 8.80 | MPa | ASTM D412 |
| yield | 11.3 | MPa | ASTM D412 |
| yield | 13.8 | MPa | ASTM D412 |
| Tensile strain | ASTM D412 | ||
| fracture | 280 | % | ASTM D412 |
| fracture | 230 | % | ASTM D412 |
| fracture | 300 | % | ASTM D412 |
| fracture | 190 | % | ASTM D412 |
| fracture | 150 | % | ASTM D412 |
| fracture | 220 | % | ASTM D412 |
| Compression deformation | ASTM D395 | ||
| 150℃，70 hr | 16 | % | ASTM D395 |
| 150℃，168 hr | 21 | % | ASTM D395 |
| 150℃，336 hr | 26 | % | ASTM D395 |
| 150℃，504 hr | 30 | % | ASTM D395 |
| 150℃，1008 hr | 40 | % | ASTM D395 |
| 177℃，168 hr | 24 | % | ASTM D395 |
| Aging performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume change | ASTM D471 | ||
| 150 ℃, 70 hr, ASTM standard oil (No.1) | 9.0 | % | ASTM D471 |
| 150 ℃, 70 hr, in IRM 903 oil | 60 | % | ASTM D471 |
| 150℃，1008 hr，Dexron® III ATF | 28 | % | ASTM D471 |
| 150 ℃, 1008 hr, in SF105 oil | 32 | % | ASTM D471 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Embrittlement temperature | ASTM D3418 | ||
| — | -32.6 | ℃ | ASTM D3418 |
| — | -27.9 | ℃ | ASTM D3418 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Mooney Scorch（Time to 10unit rise，121℃） | 13.0 | min | ASTM D1646 |
| volatility | < 0.4 | wt% | Internal Method |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Aged 70 Hrs at 150°C (302°F) Immersed in IRM 903 |
| 3. Aged 1008 Hrs at 150°C (302°F) Immersed in SF-105 Oil |
| 4. Aged 1008 Hrs at 150°C (302°F) Immersed in GM Dexron® III ATF |
| 5. Aged 1008 Hrs at 150°C (302°F) in Air |
| 6. Aged 70 Hrs at 150°C (302°F) Immersed in ASTM #1 Oil |
| 7. Initial |
| 8. Inflection |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |