| About |
|---|
| 43% glass and mineral reinforced grade. Glass and mineral filled grade, high flow and low warpage. Chemical abbreviation according to ISO 1043-1 : LCP Inherently flame retardant&& |
| Product Description | |
|---|---|
| Supplier | Celanese |
| Generic | 液态聚合物 |
| Material Status | Commercial: Active |
| Features | Low warping,High liquidity,Flame Characteristics |
| Availabilitys | North America,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.77 | g/cm³ | ISO 1183 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 13000 | MPa | ISO 527-2/1A/1 |
| tensile strength | |||
| fracture | 130 | MPa | ISO 527-2/1A/5 |
| Tensile strain | |||
| fracture | 1.7 | % | ISO 527-2/1A/5 |
| Bending modulus | |||
| 23℃ | 12700 | MPa | ISO 178 |
| bending strength | |||
| 23℃ | 170 | MPa | ISO 178 |
| Fracture bending strain | 1.9 | % | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 5.8 | kJ/m² | ISO 179/1eA |
| Charpy Unnotch Impact strength | |||
| 23℃ | 26 | kJ/m² | ISO 179/1eU |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 262 | ℃ | ISO 75-2/A |
| 0.45 MPa, unannealed | 286 | ℃ | ISO 75-2/B |
| Melting temperature | 328 | ℃ | ISO 11357-3 |
| Linear coefficient of thermal expansion | |||
| TD | 3.8E-5 | 1/℃ | ISO 11359-2 |
| MD | 9.0E-6 | 1/℃ | ISO 11359-2 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | 1.0E+16 | ohms | IEC 60093 |
| Volume resistivity | 1.0E+16 | ohms·cm | IEC 60093 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 150 to 170 | °C | |
| Drying time | 6.0 | hr | |
| Recommended maximum moisture content | 0.010 | % | |
| Barrel rear temperature | 315 to 325 | °C | |
| Barrel middle temperature | 325 to 335 | °C | |
| Barrel front temperature | 330 to 350 | °C | |
| Nozzle temperature | 330 to 340 | °C | |
| Processing (melt) temperature | 335 to 345 | °C | |
| Mold temperature | 80 to 130 | °C | |
| Injection pressure | 50.0 to 150 | MPa | |
| Injection speed | Moderate-Fast | ||
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 10°C/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |