| About |
|---|
| Viton® Extreme™ ETP-600S is an improved processing version of Viton® ETP-900, designed to match ETP-900 as closely as possible in terms of fluid resistance. The monomer composition of ETP-600S is virtually identical to ETP-900, but due to an optimized polymer architecture, compounds based on Viton® Extreme™ ETP-600S exhibit the following: Faster cure rates Improved flow at high shear rates Slightly higher tensile strength Improved resistance to compression set Equivalent fluid and chemical resistance Compounds based on ETP-600S can be readily processed in the same manner used for mixing, preforming, and molding conventional fluoroelastomers. Processors will note that compounds based on ETP-600S will typically mix slightly faster, extrude somewhat more smoothly, and exhibit less mold sticking than the same compound based on ETP-900.&& |
| Product Description | |
|---|---|
| Supplier | Chemours |
| Generic | 氟橡胶 |
| Material Status | Commercial: Active |
| Features | Good Dimensional Stability,Good liquidity,Good stripping performance,Good Tensile Strength,Solvent resistance |
| Availabilitys | North America,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.82 | g/cm³ | ASTM D792 |
| Mooney viscosity | |||
| ML 1+10，121℃ | 60 | MU | ASTM D1646 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | ASTM D2240 | ||
| Shore A, 23 ℃ | 60 | ASTM D2240 | |
| Shore A, 23 ℃ | 75 | ASTM D2240 | |
| Shore A, 23 ℃ | 76 | ASTM D2240 | |
| Shore A, 23 ℃ | 76 | ASTM D2240 | |
| Shore A, 23 ℃ | 75 | ASTM D2240 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | ASTM D412 | ||
| 50% strain, 23 ℃ | 2.80 | MPa | ASTM D412 |
| 50% strain, 23 ℃ | 2.30 | MPa | ASTM D412 |
| 50% strain, 23 ℃ | 1.30 | MPa | ASTM D412 |
| 50% strain, 23 ℃ | 2.70 | MPa | ASTM D412 |
| 50% strain, 23 ℃ | 2.20 | MPa | ASTM D412 |
| 100% strain, 23 ℃ | 4.00 | MPa | ASTM D412 |
| 100% strain, 23 ℃ | 7.20 | MPa | ASTM D412 |
| 100% strain, 23 ℃ | 6.20 | MPa | ASTM D412 |
| 100% strain, 23 ℃ | 7.90 | MPa | ASTM D412 |
| 100% strain, 23 ℃ | 7.00 | MPa | ASTM D412 |
| tensile strength | ASTM D412 | ||
| Yield, 23 ℃ | 10.1 | MPa | ASTM D412 |
| Yield, 23 ℃ | 17.2 | MPa | ASTM D412 |
| Yield, 23 ℃ | 15.7 | MPa | ASTM D412 |
| Yield, 23 ℃ | 18.3 | MPa | ASTM D412 |
| Yield, 23 ℃ | 15.9 | MPa | ASTM D412 |
| Tensile strain | ASTM D412 | ||
| Fracture, 23 ℃ | 200 | % | ASTM D412 |
| Fracture, 23 ℃ | 220 | % | ASTM D412 |
| Fracture, 23 ℃ | 220 | % | ASTM D412 |
| Fracture, 23 ℃ | 230 | % | ASTM D412 |
| Fracture, 23 ℃ | 270 | % | ASTM D412 |
| Compression deformation | ASTM D395B | ||
| 150℃，70 hr | 34 | % | ASTM D395B |
| 150℃，336 hr | 50 | % | ASTM D395B |
| 200℃，70 hr | 51 | % | ASTM D395B |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 20 in/min |
| 3. Aged 168 hr at 100°C in 30% potassium hydroxide in water |
| 4. Aged 168 hr at 150°C in Axle Lubricant with 6% high pH additive |
| 5. Aged 168 hr at 23°C in MEK |
| 6. Aged 16 hr at 200°C |
| 7. Aged 168 hr at 250°C |
| 8. 20 in/min, Aged in MEK for 168 hr at 73°F |
| 9. 20 in/min, Aged in Potassium Hydroxide 30% for 168 hr at 212°F |
| 10. 20 in/min, Aged in Axle Lubricant with 6% High pH Additive for 168 hr at 302°F |
| 11. 20 in/min, Aged for 16 hr at 392°F |
| 12. 20 in/min, Aged for 168 hr at 482°F |
| 13. Aged in MEK for 168 hr at 73°F |
| 14. Aged in Potassium Hydroxide 30% for 168 hr at 212°F |
| 15. Aged in Axle Lubricant with 6% High pH Additive for 168 hr at 302°F |
| 16. Aged for 16 hr at 392°F |
| 17. Aged for 168 hr at 482°F |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |