Vydyne® 21SPM

About
Vydyne 21SPM is a general-purpose PA66 resin. Available in natural, it is designed principally for injection-molding fabrication. This grade offers a well-balanced combination of engineering properties characterized by high strength; rigidity; good toughness; high melt point; good surface lubricity; abrasion resistance and resistance to many chemicals, machine and motor oils, solvents and gasoline. Vydyne 21SPM resin permits production of molded parts with good initial color plus good property and color retention when using regrind. This resin is recognized by Underwriters Laboratories and conforms to the requirements of many industrial, federal and military specifications for premium-quality, general-purpose PA66 resins. Vydyne 21SPM resin is internally and externally lubricated for improved machine feed and exceptional mold release. It is intended for use in high-productivity applications. In many applications, the molding cycle can be reduced because parts may be removed from the cavity at higher temperatures. In difficult molds where parts have a tendency to stick in the cavity, Vydyne 21SPM can reduce or eliminate the need for mold release sprays. Critical molded part dimensions should be checked against specifications before implementing shorter molding cycles on a routine production basis.

About

Vydyne 21SPM is a general-purpose PA66 resin. Available in natural, it is designed principally for injection-molding fabrication. This grade offers a well-balanced combination of engineering properties characterized by high strength; rigidity; good toughness; high melt point; good surface lubricity; abrasion resistance and resistance to many chemicals, machine and motor oils, solvents and gasoline. Vydyne 21SPM resin permits production of molded parts with good initial color plus good property and color retention when using regrind. This resin is recognized by Underwriters Laboratories and conforms to the requirements of many industrial, federal and military specifications for premium-quality, general-purpose PA66 resins. Vydyne 21SPM resin is internally and externally lubricated for improved machine feed and exceptional mold release. It is intended for use in high-productivity applications. In many applications, the molding cycle can be reduced because parts may be removed from the cavity at higher temperatures. In difficult molds where parts have a tendency to stick in the cavity, Vydyne 21SPM can reduce or eliminate the need for mold release sprays. Critical molded part dimensions should be checked against specifications before implementing shorter molding cycles on a routine production basis.

Product Description
Supplier	Ascend
Generic	PA66
Material Status	Commercial: Active
Features	Good Rigidity,Good flexibility,Quick molding cycle,Good stripping performance,Lubricating,Good wear resistance,Grease resistance,Solvent resistance,Gasoline resistance
Availabilitys	North America,Asia Pacific,Europe
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.14	g/cm³
Shrinkage rate
TD：23℃，2.0 mm	2.0	%
TD：23℃，2.0 mm	2.0	%
Water absorption rate
23℃，24hr	1.2	%
Equilibrium, 23 ℃, 50% RH	2.4	%
Outdoor applicability (all)	f2

MECHANICAL	Nominal value	Unit
Tensile modulus
23℃	3300	MPa
Tensile stress
Yield, 23 ° C	88.0	MPa
Fracture, 23 ° C	60.0	MPa
Tensile strain
Yield, 23 ℃	5.0	%
Nominal tensile fracture strain (23 ° C)	20	%
Bending modulus
23℃	3300	MPa
bending strength
23℃	105	MPa
Poisson’s ratio	0.40

IMPACT	Nominal value	Unit
Charpy Notched Impact Strength
-30℃	5.0	kJ/m²
23℃	6.0	kJ/m²
Charpy Unnotch Impact strength
-30℃	无断裂
23℃	无断裂
Impact strength of cantilever beam notch
-30℃	5.0	kJ/m²
23℃	6.0	kJ/m²

THERMAL	Nominal value	Unit
Hot deformation temperature
0.45 MPa, unannealed	210	℃
1.8 MPa, unannealed	72.0	℃
Melting temperature	260	℃
Linear coefficient of thermal expansion
Flow: 23~55 ° C, 2.00 mm	1.0E-4	1/℃
TD：23~55℃，2.00 mm	1.0E-4	1/℃
RTI Elec
0.40 mm	130	°C
0.71 mm	130	°C
1.5 mm	130	°C
3.0 mm	130	°C
RTI Imp
0.40 mm	75.0	°C
0.71 mm	75.0	°C
1.5 mm	75.0	°C
3.0 mm	75.0	°C
RTI
0.40 mm	75.0	°C
0.71 mm	85.0	°C
1.5 mm	85.0	°C
3.0 mm	85.0	°C

Electrical performance	Nominal value	Unit
Volume resistivity
0.75 mm	1.0E+13	ohms·cm
Dielectric strength
1 mm	26	kV/mm
Arc resistance
3.00 mm	PLC 5
Compared to the leakage tracing index
3.00 mm	600	V
High Arc Burning Index (HAI)
0.40 mm	PLC 1
0.71 mm	PLC 0
1.5 mm	PLC 0
3.0 mm	PLC 0
High voltage arc marking rate (HVTR)	PLC 0
Hot wire ignition (HWI)
0.40 mm	PLC 4
0.71 mm	PLC 4
1.5 mm	PLC 3
3.0 mm	PLC 2

FLAME CHARACTERISTICS	Nominal value	Unit
Flame retardant level
0.40 mm	V-2
0.71 mm	V-2
1.50 mm	V-2
3.00 mm	V-2
Glowing wire flammability index
0.40 mm	960	℃
0.71 mm	960	℃
1.5 mm	960	℃
3.0 mm	960	℃
Hot filament ignition temperature
0.40 mm	825	°C
0.71 mm	850	°C
1.5 mm	850	°C
3.0 mm	850	°C
Extreme oxygen index	26	%

Process Conditions
Injection	Nominal value	Unit	Test method
drying temperature	< 70	°C
Drying time	1.0 to 3.0	hr
Suggested maximum proportion of recycled materials	50	%
Temperature at the rear of the barrel	260 to 280	°C
Temperature in the middle of the barrel	270 to 285	°C
Front temperature of material barrel	280 to 290	°C
Nozzle temperature	280 to 300	°C
Processing (melt) temperature	285 to 300	°C
Mold temperature	65 to 95	°C

Notes
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.