| About |
|---|
| DSM’s Somos® WaterClear Ultra 10122 is a next generation optically clear resin with ABS-like properties and good temperature resistance. It produces colorless, functional, accurate parts that simulate an acrylic appearance. Based on the Oxetane Advantage™, the parts also have improved water- resistance over the original Somos® WaterClear 10120 resin. Somos® WaterClear Ultra is a fast, low viscosity, general-purpose resin. Applications This high-temperature resistant, ABS-like photopolymer is used in solid imaging processes, like stereolithography, to build three-dimensional parts. Somos® WaterClear Ultra is ideal for applications requiring optical clarity, such as automotive lenses, bottles, fluid flow analysis, packaging prototypes, light pipes and more. Somos® WaterClear Ultra can also be used for concept, functional models and master patterns.&& |
| Product Description | |
|---|---|
| Supplier | DSM |
| Generic | 3D打印材料 |
| Material Status | Commercial: Active |
| Features | Good Clarity,High purity,Low Viscosity,Optical performance,High Heat Resistance |
| Availabilitys | North America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.13 | g/cm³ | |
| Water absorption rate | |||
| balance | 1.1 | % | ASTM D570 |
| viscosity | |||
| 30℃ | 0.165 | Pa·s | |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | 23 to 26 | J/m | ASTM D256-A |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | ASTM D648 | ||
| 0.45 MPa, unannealed | 46.0 to 47.0 | ℃ | ASTM D648 |
| 0.45 MPa, unannealed | 59.0 to 61.0 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed | 42.0 to 43.0 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed | 49.0 to 50.0 | ℃ | ASTM D648 |
| Glass transition temperature | 42.0 to 46.0 | ℃ | ASTM E1545 |
| Linear coefficient of thermal expansion | |||
| MD | ASTM E831 | ||
| -40 to 0 ℃ | 6.4E-5 to 6.7E-5 | cm/cm/℃ | ASTM E831 |
| 0 to 50 ℃ | 8.8E-5 to 9.3E-5 | cm/cm/℃ | ASTM E831 |
| 50 to 100 ℃ | 1.6E-4 to 1.7E-4 | cm/cm/℃ | ASTM E831 |
| 100 to 150 ℃ | 1.5E-4 to 1.7E-4 | cm/cm/℃ | ASTM E831 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Dielectric strength | 15 to 16 | kV/mm | ASTM D149 |
| Dielectric constant | ASTM D150 | ||
| 60 Hz | 3.00 to 3.20 | ASTM D150 | |
| 1 kHz | 3.30 to 3.60 | ASTM D150 | |
| 1 MHz | 3.00 to 3.20 | ASTM D150 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Refractive index | 1.520 | ASTM D542 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Critical Exposure | 10.0 | mJ/cm² | |
| Penetration depth | 165.1 | µm |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s D | 86 to 87 | ASTM D2240 | |
| Tensile modulus | 2860 to 2900 | MPa | ASTM D638 |
| tensile strength | |||
| fracture | 55.0 to 56.0 | MPa | ASTM D638 |
| Tensile strain | ASTM D638 | ||
| yield | 4.0 | % | ASTM D638 |
| fracture | 6.0 to 9.0 | % | ASTM D638 |
| Bending modulus | 2410 to 2570 | MPa | ASTM D790 |
| bending strength | 82.0 to 85.0 | MPa | ASTM D790 |
| Poisson’s ratio | 0.40 to 0.42 | ASTM D638 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. with Thermal Postcure |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |