| About |
|---|
| Witcom PA6 2004/39 is a Polyamide 6 (Nylon 6) product filled with filler. It can be processed by injection molding and is available in Europe. Characteristics include: Flame Rated Conductive&& |
| Product Description | |
|---|---|
| Generic | PA6 |
| Material Status | Commercial: Active |
| Features | Conductive,HB |
| Availabilitys | Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.31 | g/cm³ | ISO 1183 |
| Shrinkage rate | |||
| MD：3.0 mm | 0.20 to 0.40 | % | ISO 2577 |
| Water absorption rate | ISO 62 | ||
| Saturation, 23 ℃ | 6.0 | % | ISO 62 |
| Equilibrium, 23 ℃, 50% RH | 2.0 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | ISO 527-2 | ||
| -40℃ | 7600 | MPa | ISO 527-2 |
| 23℃ | 7000 | MPa | ISO 527-2 |
| 80℃ | 3600 | MPa | ISO 527-2 |
| tensile strength | ISO 527-2 | ||
| Fracture, -40 ℃ | 155 | MPa | ISO 527-2 |
| Fracture, 23 ℃ | 110 | MPa | ISO 527-2 |
| Fracture, 80 ℃ | 65.0 | MPa | ISO 527-2 |
| Tensile strain | ISO 527-2 | ||
| Fracture, -40 ℃ | 1.0 to 3.0 | % | ISO 527-2 |
| Fracture, 23 ℃ | 2.0 to 4.0 | % | ISO 527-2 |
| Fracture, 80 ℃ | 5.0 to 7.0 | % | ISO 527-2 |
| Bending modulus | |||
| 23℃ | 6200 | MPa | ISO 178 |
| bending strength | |||
| 23℃ | 155 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | ISO 180/1A | ||
| -40℃ | 8.0 | kJ/m² | ISO 180-1A |
| 23℃ | 11 | kJ/m² | ISO 180-1A |
| Notched impact strength of cantilever beam | ISO 180/1U | ||
| -40℃ | 50 | kJ/m² | ISO 180/1U |
| 23℃ | 60 | kJ/m² | ISO 180/1U |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 195 | ℃ | ISO 75-2/A |
| Linear coefficient of thermal expansion | |||
| MD | 3.7E-5 | 1/℃ | ISO 11359-2 |
| Relative temperature index | |||
| Impact mechanical performance, 3.00 mm | 95.0 | ℃ | UL 746 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | 1.0E+4 to 1.0E+6 | ohms | ASTM D257 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 3.00 mm | HB | ISO 1210 | |
| Glowing wire flammability index | |||
| 1.6 mm | 750 | ℃ | IEC 60695-2-12 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 80 | °C | |
| Drying time | 3.0 to 5.0 | hr | |
| Recommended maximum moisture content | 0.10 | % | |
| Processing (melt) temperature | 250 to 270 | °C | |
| Mold temperature | 40 to 80 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |