| About |
|---|
| Product Description | |
|---|---|
| Supplier | CHI MEI |
| Generic | PC+ABS |
| Material Status | Commercial: Active |
| Features | Halogen free,Flame Characteristics,Heat Stabilized |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | |||
| 23℃ | 1.18 | g/cm³ | ASTM D792 |
| Shrinkage rate | 0.4-0.6 | % | ASTM D955 |
| Melt Volume Rate | |||
| 260℃，2.16kg | 20 | cm³/10min | ASTM D1238 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 3.2mm,1.82Mpa，120℃/hrs | 86 | ℃ | ASTM D648 |
| 6.4mm,1.82Mpa，120℃/hrs | 95 | ℃ | ASTM D648 |
| Vicat Softening Temp | |||
| 1kg, 50℃/hrs | 108 | ℃ | ASTM D1525 |
| 5kg, 50℃/hrs | 101 | ℃ | ASTM D1525 |
| Linear coefficient of thermal expansion | |||
| MD：23-55℃ | 8.00E-05 | cm/cm/℃ | ISO11359-2 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.50mm | V-0 | UL 94 | |
| 2.00mm | 5VB | UL 94 | |
| 3.00mm | 5VA | UL 94 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | 441 | J/m | ASTM D256 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | |||
| R-level | 119 | ASTM D785 | |
| tensile strength | |||
| Yield, 50mm/min | 58.80 | MPa | ASTM D638 |
| Fracture, 50mm/min | 53.9 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | 100 | % | ASTM D638 |
| yield | 4 | % | ASTM D638 |
| bending strength | |||
| 1.3mm/min | 88.2 | MPa | ASTM D790 |
| Bending modulus | |||
| 1.3mm/min | 2500 | MPa | ASTM D790 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Dielectric constant | |||
| 1MHz | 3.1 | IEC 60250 | |
| Volume resistivity | 3.9E+17 | Ohm*m | IEC 60093 |
| Surface resistivity | 2.9E+17 | Ohm | IEC 60093 |
| Process Conditions | |||
|---|---|---|---|
| Injection | Nominal value | Unit | Test method |
| drying temperature | 80 | °C | |
| Drying time | 3-4 | Hr | |
| Injection temperature | |||
| Mold head temperature | 240-280 | °C | |
| Mold temperature | 50-100 | °C | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |