| About |
|---|
| XAREC™ N WA 7020 is a Syndiotactic Polystyrene + PA (SPS+Nylon) product filled with 20% glass fiber. It is available in Africa & Middle East, Asia Pacific, Europe, Latin America, or North America. Primary characteristic: flame rated.&& |
| Product Description | |
|---|---|
| Supplier | Idemitsu |
| Generic | Syndiotactic Polystyrene +PA |
| Material Status | Commercial: Active |
| Features | HB |
| Availabilitys | North America,Asia Pacific,Europe,Africa & Middle East ,Latin America |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.25 | g/cm³ | ISO 1183 |
| Water Absorption | |||
| 24 h，50%r.h. | 0.22 | % | ISO 62 |
| Molding shrinkage | |||
| Flowing flow | 0.3-0.6 | % | 内部 |
| Cross flow | 0.7-1.0 | % | 内部 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile Strength | |||
| Broken BRK | 150 | MPa | ISO 527-2 |
| Tensile Modulus | 7300 | MPa | ISO 527 |
| Elongation at Break | 2.9 | % | ISO 527 |
| Flexural Strength | 215 | MPa | ISO 178 |
| Flexural Modulus | 6700 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Izod Notched Impact strength | 8 | KJ/m² | ISO 180/1A |
| Izod Unnotched Impact strength of cantilever beam | 45 | KJ/m² | ISO 180/1U |
| Charpy Notched Impact Strength | 9 | kJ/m² | ISO 179/1eA |
| Charpy Unnotch Impact strength | 55 | kJ/m² | ISO 179/1eU |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature HDT | |||
| 1.8 MPa | 245 | ℃ | ISO 75-1/-2 |
| 0.45 MPa | 260 | ℃ | ISO 75-1/-2 |
| Coeff. of linear thermal expansion | |||
| flow | 30 | mm/mm/℃ | TMA |
| Lateral flow | 54 | mm/mm/℃ | TMA |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame Class Rating | |||
| 1.5 mm | HB | UL 94 | |
| Relative temperature of heating wire | |||
| electrical | 50 | ℃ | UL 746B |
| Mechanical impact | 50 | ℃ | UL 746B |
| Non mechanical impact | 50 | ℃ | UL 746B |
| ELECTRICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Compared Tracking Index | 1 | PLC Code | IEC 60112 |
| High Voltage Arc Track Rate | — | PLC Code | UL 746A |
| Hot wire ignition | |||
| 3.0 mm | 4 | PLC Code | UL 746A |
| 1.5 mm | 5 | PLC Code | UL 746A |
| 0.75 mm | — | PLC Code | UL 746A |
| High Arc Burning Index (HAI) | |||
| 3.0 mm | 0 | PLC Code | UL 746A |
| 1.5 mm | 0 | PLC Code | UL 746A |
| 0.75 mm | — | PLC Code | UL 746A |
| Arc Resistance | 5 | PLC Code | ASTM D495 |
| Volume Resistance | 3.1E15 | ohm·cm | IEC 60093 |
| Dielectric Strength | 25 | kV/mm | ASTM D149 |
| Dielectric Constant | 3.1 | IEC 60250 | |
| Dissipation Factor | 0.034 | IEC 60250 |
| Process Conditions | |||
|---|---|---|---|
| Injection Molding | Nominal value | Unit | Test method |
| Drying Temperature | 80 | ℃ | |
| Drying Time | 3-5 | hr | |
| Melt Temperature | 280-310 | ℃ | |
| Mold Temperature | 50-80 | ℃ | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 24h |
| 3. Solution A |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |