| About |
|---|
| Modified PPE PP/PPE alloy Non-reinforced Dimensional stability Good&& |
| Product Description | |
|---|---|
| Supplier | Asahi Kasei |
| Generic | PPO(PPE)+PP |
| Material Status | Commercial: Active |
| Features | Good Dimensional Stability |
| Availabilitys | Africa & Middle East ,North America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.928 | g/cm³ | ISO 1183 |
| Shrinkage rate | |||
| 3.0 mm | 2.0 to 2.5 | % | Internal Method |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| Yield, 23 ℃ | 37.0 | MPa | ISO 527-2 |
| Tensile strain | |||
| Fracture, 23 ℃ | 51 | % | ISO 527-2 |
| Bending modulus | |||
| 23℃ | 2050 | MPa | ISO 178 |
| bending strength | |||
| 23℃ | 57.0 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 19 | kJ/m² | ISO 179 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 90.0 | ℃ | ISO 75-2/A |
| 1.8 MPa, unannealed | 97.0 | ℃ | ASTM D648 |
| Linear coefficient of thermal expansion | |||
| MD：-30~65℃ | 9.0E-5 | 1/℃ | ISO 11359-2 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | |||
| 23℃ | 8.4E+16 | ohms·cm | IEC 60093 |
| Dielectric strength | |||
| 2 mm | 30 | kV/mm | IEC 60243-1 |
| Dielectric constant | IEC 60250 | ||
| 100 Hz | 2.30 | IEC 60250 | |
| 1 MHz | 2.30 | IEC 60250 | |
| Dissipation factor | IEC 60250 | ||
| 100 Hz | 2.0E-4 | IEC 60250 | |
| 1 MHz | 5.0E-4 | IEC 60250 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 80 to 90 | °C | |
| Drying time | 1.0 to 2.0 | hr | |
| Processing (melt) temperature | 230 to 260 | °C | |
| Mold temperature | 50 to 70 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 120x80x3 mm |
| 3. 4 mm |
| 4. Short Time |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |