| About |
|---|
| Product Description | |
|---|---|
| Supplier | Celanese |
| Material Status | Commercial: Active |
| Features | Heat Stabilized |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Viscosity number | 3320 | in³/lb | ISO 307, 1157, 1628 |
| Molding shrinkage | |||
| Parallel | 0.3 | % | ISO 294-4 |
| Normal | 0.9 | % | ISO 294-4 |
| Moisture Absorption | 2 | % | ISO 62 |
| Water Absorption | 0.4 | % | ISO 62 |
| Density | 12.1 | lb/gal | ISO 1183 |
| Density of melt | 68.7 | lb/ft³ | |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile Modulus | |||
| Dry | 11730 | MPa | ISO 527 |
| Wet Cond | 11730 | MPa | ISO 527 |
| Tensile Stress | |||
| Broken BRK, dry dry | 207 | MPa | ISO 527 |
| Broken BRK, wet Cond | 179.4 | MPa | ISO 527 |
| Tensile Strain | |||
| Broken BRK, dry dry | 2.6 | % | ISO 527 |
| Broken BRK, wet Cond | 2.6 | % | ISO 527 |
| Flexural Strength | 10419 | MPa | ISO 178 |
| Flexural Modulus | 290.49 | MPa | ISO 178 |
| Poisson’s ratio | |||
| Dry | 0.33 | ||
| Wet Cond | 0.33 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Unnotch Impact strength | 60.9 | kJ/m² | ISO 179/1eU |
| Charpy Notched Impact Strength | 10.08 | kJ/m² | ISO 179/1eA |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Melting temperature | |||
| 10°C/min | 310 | ℃ | ISO 11357-3 |
| First heat | 310 | ℃ | ISO 11357-3 |
| Glass Transition Temperature | |||
| Dry | 90 | ℃ | ISO 11357-2 |
| Wet Cond | 45 | ℃ | ISO 11357-2 |
| Hot deformation temperature HDT | |||
| 1.8 MPa | 282.2 | ℃ | ISO 75-1/-2 |
| Coeff. of linear thermal expansion | |||
| Parallel | 0.11 | E-4/°F | ISO 11359-2 |
| Normal | 0.361 | E-4/°F | ISO 11359-2 |
| Thermal conductivity | 0.24 | W/m/K |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Oxygen Index | 23 | % | ISO 4589-2 |
| Glow Wire Flammability Index (GWFI) | 960 | ℃ | IEC 60695-2-12 |
| Glow Wire Ignitability Temperature (GWIT) | 799 | ℃ | IEC 60695-2-13 |
| FMVSS flame retardant rating | B | FMVSS 302 | |
| Burning Speed | 1.73 | in/min | FMVSS 302 |
| ELECTRICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Relative permittivity | |||
| 100 Hz | 4.3 | IEC 62631-2-1 | |
| 1 MHz | 4.2 | IEC 62631-2-1 | |
| Dissipation Factor | |||
| 1 MHz | 147 | E-4 | IEC 62631-2-1 |
| 1 GHz | 124 | E-4 | IEC 62631-2-1 |
| 23°C, 10 GHz | 113 | E-4 | IEC 62631-2-1 |
| Volume Resistance | >1E13 | ohm·m | IEC 62631-3-1 |
| Surface Resistivity | >1E15 | ohm | IEC 62631-3-2 |
| Electric strength | |||
| Dry | 787 | kV/in | IEC 60243-1 |
| Wet Cond | 762 | kV/in | IEC 60243-1 |
| Compared Tracking Index | 600 | IEC 60112 | |
| Dielectric Constant | |||
| 1 GHz | 3.82 | IEC 60250 | |
| 23°C, 10 GHz | 3.92 | IEC 60250 |
| Process Conditions | |||
|---|---|---|---|
| Injection Molding | Nominal value | Unit | Test method |
| Drying Temperature | 100 | ℃ | |
| Drying Time | 6.0 to 8.0 | hr | |
| Maximum Moisture Content | 0.10 | % | |
| Melt Temperature | 320 to 330 | ℃ | |
| Melt Temperature, Optimal | 325 | ℃ | |
| Mold Temperature | 90 to 110 | ℃ | |
| Drying Recommended | yes | ℃ | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |