| About |
|---|
| 45% Glass Reinforced, PPA, High Performance Polyamide&& |
| Product Description | |
|---|---|
| Supplier | Celanese |
| Material Status | Commercial: Active |
| Features | Heat Stabilized |
| Availabilitys | Europe,North America,Africa & Middle East ,Asia Pacific,Latin America |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| MECHANICAL | Nominal value | Unit | Test method |
| Tensile Modulus | 15180 | MPa | ISO 527 |
| Tensile Stress | 234.6 | MPa | ISO 527 |
| Tensile Strain | 2 | % | ISO 527 |
| Poisson’s ratio | 0.33 | ||
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Unnotch Impact strength | 65.1 | kJ/m² | ISO 179/1eU |
| Charpy Notched Impact Strength | 11.97 | kJ/m² | ISO 179/1eA |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Melting temperature | 310 | ℃ | ISO 11357-3 |
| Glass Transition Temperature | |||
| Dry | 90 | ℃ | ISO 11357-2 |
| Wet Cond | 45 | ℃ | ISO 11357-2 |
| Coeff. of linear thermal expansion | |||
| Parallel, -40-23 ° C | 0.944 | E-4/°F | ISO 11359-2 |
| Parallel | 0.09 | E-4/°F | ISO 11359-2 |
| Parallel, 55-160 ° C | 0.0833 | E-4/°F | ISO 11359-2 |
| Normal, -40-23 ° C | 0.3 | E-4/°F | ISO 11359-2 |
| Normal | 0.322 | E-4/°F | ISO 11359-2 |
| Normal, 55-160 ° C | 0.556 | E-4/°F | ISO 11359-2 |
| Thermal conductivity | 0.26 | W/m/K | |
| Specification of Heat Capacity of Melt | 0.771 | BTU/(lb·F) |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| FMVSS flame retardant rating | B | FMVSS 302 | |
| Burning Speed | 0.669 | in/min | FMVSS 302 |
| PHYSICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Density | 13 | lb/gal | ISO 1183 |
| Density of melt | 90.5 | lb/ft³ |
| Process Conditions | |||
|---|---|---|---|
| Injection Molding | Nominal value | Unit | Test method |
| Drying Temperature | 100 | °C | |
| Drying Time | 6.0 to 8.0 | hr | |
| Maximum Moisture Content | 0.10 | % | |
| Melt Temperature | 320 to 330 | °C | |
| Melt Temperature, Optimal | 325 | °C | |
| Mold Temperature | 90 to 110 | °C | |
| Drying Recommended | yes | ||
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. FMVSS 302 |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |