| About |
|---|
| The BASF Ultramid® FC (Food Contact) grades enable the industry to develop products for food contact applications which are in compliance with multiple regional food contact regulations including FDA, European Food Contact (EU) Nr. 11/2011 and GMP (EC) n°2023/2006. Additional food contact compliances may also be available. Please contact your local representative or plastics safety (E-Mail: plastics.safety@basf.com, Fax: +49 621-60-93253).&& |
| Product Description | |
|---|---|
| Supplier | BASF |
| Generic | PA 6/6T |
| Material Status | Commercial: Active |
| Features | Food contact compliance |
| Availabilitys | Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.50 | g/cm³ | ISO 1183 |
| Shrinkage rate | ISO 294-4 | ||
| TD | 0.90 | % | |
| MD | 0.30 | % | |
| Shrinkage rate – constrained | 0.45 | % | |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 13500 | MPa | ISO 527-2 |
| tensile strength | |||
| fracture | 230 | MPa | ISO 527-2 |
| Tensile strain | |||
| fracture | 2.5 | % | ISO 527-2 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 9.0 | kJ/m² | ISO 179/1eA |
| Charpy Unnotch Impact strength | |||
| 23℃ | 80 | kJ/m² | ISO 179/1eU |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 250 | ℃ | ISO 75-2/A |
| Melting temperature | 294 | ℃ | ISO 11357-3 |
| Maximum operating temperature | |||
| short cycle operation | 260 | ℃ |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 110 | °C | |
| Drying time | 8.0 | hr | |
| Recommended maximum moisture content | 0.15 | % | |
| Hopper temperature | 80.0 | °C | |
| Barrel rear temperature | 300 | °C | |
| Barrel middle temperature | 310 | °C | |
| Barrel front temperature | 320 | °C | |
| Nozzle temperature | 320 | °C | |
| Processing (melt) temperature | 310 to 330 | °C | |
| Mold temperature | 80.0 to 120 | °C | |
| Screw Speed | mm/sec | ||
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Test box with central gating, dimensions of base (107*47*1,5) mm, processing condition: TM = 320°C (unreinforced) or 330°C (reinforced), TW = 80°C |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |