| About |
|---|
| Ultramid T KR 4365 G5 is a 25% glass fiber reinforced, flame-retardant, injection molding PA6/6T grade. Good mechanical properties, high tracking resistance, low tendency for deposits on electrical contacts, very resistant to electrolytic corrosion, resistant to solder baths; electroplateable.&& |
| Product Description | |
|---|---|
| Supplier | BASF |
| Generic | PA 6/6T |
| Material Status | Commercial: Active |
| Features | Corrosion Resistant,Flame Characteristics,Copolymer,Electric mark,V-2,V-0,5VA |
| Availabilitys | North America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.38 | g/cm³ | ISO 1183 |
| Water absorption rate | |||
| Saturation, 23 ℃ | 5.5 | % | ISO 62 |
| Equilibrium, 23 ℃, 50% RH | 1.3 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| 23℃ | 8300 | MPa | ISO 527-2 |
| tensile strength | ISO 527-2 | ||
| Fracture, -40 ℃ | 192 | MPa | ISO 527-2 |
| Fracture, 23 ℃ | 150 | MPa | ISO 527-2 |
| Fracture, 80 ℃ | 96.0 | MPa | ISO 527-2 |
| Tensile strain | ISO 527-2 | ||
| Fracture, -40 ℃ | 2.9 | % | ISO 527-2 |
| Fracture, 23 ℃ | 3.0 | % | ISO 527-2 |
| Fracture, 80 ℃ | 2.5 | % | ISO 527-2 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179 | ||
| -30℃ | 7.0 | kJ/m² | ISO 179 |
| 23℃ | 13 | kJ/m² | ISO 179 |
| Charpy Unnotch Impact strength | ISO 179 | ||
| -30℃ | 80 | kJ/m² | ISO 179 |
| 23℃ | 75 | kJ/m² | ISO 179 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 220 | ℃ | ISO 75-2/A |
| Melting temperature | |||
| DSC | 295 | ℃ | ISO 3146 |
| Linear coefficient of thermal expansion | |||
| TD | 5.5E-5 | 1/℃ | |
| MD | 2.5E-5 | 1/℃ | |
| 0.75 mm | 140 | ℃ | UL 746 |
| 1.5 mm | 140 | ℃ | UL 746 |
| 3.0 mm | 140 | ℃ | UL 746 |
| Relative temperature index | |||
| Electrical performance | UL 746 | ||
| Strength mechanical performance | UL 746 | ||
| Impact mechanical performance | UL 746 | ||
| 0.75 mm | 100 | ℃ | UL 746 |
| 1.5 mm | 105 | ℃ | UL 746 |
| 3.0 mm | 110 | ℃ | UL 746 |
| 0.75 mm | 120 | ℃ | UL 746 |
| 1.5 mm | 130 | ℃ | UL 746 |
| 3.0 mm | 140 | ℃ | UL 746 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.0E+15 | ohms·cm | IEC 60093 |
| Dielectric constant | |||
| 1 MHz | 4.00 | IEC 60250 | |
| Dissipation factor | |||
| 1 MHz | 0.020 | IEC 60250 | |
| Compared to the leakage tracing index | 600 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | UL 94 | ||
| 0.37 mm | V-2 | UL 94 | |
| 0.75 mm | V-0 | UL 94 | |
| 3.00 mm | V-0 | UL 94 | |
| 1.50 mm | 5VA | UL 94 |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |